Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 45 / 63

5.0 Operation

5.3 System Status Messages

The remote control uses the top line of the LCD display to show the inverter/

charger’s current operation by displaying a status message

This section

will show the inverter/charger’s operating modes and the available status

messages under each mode. Use these status messages along with the

Status LED’s to determine the inverter/charger’s current operating status,

and to help troubleshoot the system if a fault occurs.
There are three operating modes of the inverter/charger:

• Inverter Mode • Charger Mode • Fault Mode

5.3.1 Inverter Mode Messages

The inverter/charger will be in the Inverter Mode when AC power (utility or genera-

tor) is not available or unacceptable to the inverter/charger’s input. The Inverter

Mode messages are Off, Searching, Inverting and Standby.

Off

– This message tells you that there is no AC available on the inverter’s

AC output. The inverter function is off and there is no utility or generator AC

power sensed on its input.

Searching

– The inverter is in the Search mode, which means the AC

loads on the inverter output are less than the Setup 02A Search Watts. The

Search mode function is used to reduce the inverter draw from the battery

and may be turned off at any time, if you want full inverter output voltage

available at all times (see the 02 Invert Setup section on page 20).

Inverting

- The inverter is providing AC voltage on its output by

Inverting power from the batteries.

•

Off

appears on the LCD; all LED’s

are off.

FAULT

PWR

CHG

INV

Off

Settings/Info...

Figure 5-2, Off Mode

FAULT

PWR

CHG

INV

Searching

Settings /Info...

Searching

appears on the LCD. The

PWR (green) LED is on solid and the

INV (green) LED slowly

ashes. The

FAULT (red) and CHG (green) LED’s

are off.

Figure 5-3, Searching Mode

FAULT

PWR

CHG

INV

Inverting

Settings/Info...

Inverting

appears on the LCD. The

PWR (green) and INV (green) LED’s

are on solid. The FAULT (red) and

CHG LED’s are off.

Figure 5-4, Inverting Mode

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды