Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 15 / 63

3.0 Setup

03 GEN Control

GEN Control is used for controlling a standby generator connected to the

system using the optional ME-AGS-N. Once the ME-AGS-N is installed in the

system, the generator can be manually started and stopped or set to the auto

start and stop mode from the GEN Control menu.

Info:

The ME-AGS-N, Multi Gen Start Network, version must be

installed in order for the 03 GEN Control menu to control a standby

generator. Refer to the ME-AGS-N manual for more information on

controlling standby generators.

OFF:

The OFF selection turns the generator OFF if it is running from either a

manual start or auto start command. When the OFF position is selected the

generator will not start automatically.

Info:

If DC power is lost to the remote, this menu resets to the

default OFF position for safety.

Restart Bulk:

This selection restarts the Bulk cycle from any stage in the

charge cycle. Restarting the Bulk stage is useful when a full Multi-stage

charge cycle does not bring the speci

c gravity of the batteries to the

proper level.

Info:

Restart Bulk will default back to the Multi-Stage once the

inverter/charger status displays “Bulk Charging”.

Info:

If you have to continually restart the Bulk cycle in order to

bring the batteries to full charge, check the settings in SETUP menu

“03 Charger Setup” to make sure the batteries are fully charged at

the end of a regular multi-stage charge cycle. Check with your bat-

tery manufacture for proper battery charger settings.

CAUTION:

Frequently restarting Bulk may result in overcharging

of the batteries.

Force Float:

This charge pro

le “forces” the charger to stay in the Float mode

as long as AC is present and the charger is active. Force Float is most often

used when another source of charging such as PV, wind or hydro is available

to keep the batteries at or above the Float voltage. If AC is disconnected and

then reconnected the charger will go directly to the Float mode and will not

do a Bulk or Absorption charge cycle.

CAUTION:

Using the Force Float mode may not fully charge the

batteries. Most batteries require a Bulk and Absorption charge cycle

in order to fully recombine the electrolyte in the batteries and bring

the speci

c gravity to the proper level. Be sure to check with your

battery manufacture before using this setting.

Info:

If Silent is selected in menu 03G Final Charge Stage you can

override this selection with Force Float to temporarily Float the

batteries.

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды