Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 36 / 63

3.0 Setup

Info:

If the correct PIN has been forgotten you may override the

entered PIN. In menu 05 SETUP PIN when “PIN = 0***” is displayed,

press and hold the Select knob until “PIN = 0000” is displayed. Enter

a new PIN number as described in 05 SETUP PIN above.

Example:

The inverter has it’s

rst fault today (D-) which is a Low Battery

Fault at 10PM and then the next day (D-1) a High Battery Fault at 11PM. The

Inv Fault History will display in order H1 =

rst fault in history, H2 = second

fault in history etc.
H1 Low Battery

H2 High Battery

H1 D- 10:00PM

H2 D-1 11:00 PM

H1 Inverting

H2 Bulk Charge

H1 22 VDC 18A

H2 32 VDC 80A

H1 BTS: 60F

H2 BTS: 60F

H1 Tfmer: 65F

H2 Tfmer: 95F

H1 FETs: 65F

H2 FETs: 80C

TECH: 05 SETUP PIN:

This menu sets the password, locks and unlocks

the “SETUP” button. The SETUP button can be locked with a password to

avoid an unauthorized change.

Why should I use the PIN feature?

This feature is useful when the

operation of the inverter has been set up by an experienced user or installer.

Setting the PIN prohibits an inexperienced user from changing settings that

might result in an undesirable operation.

Default setting:

PIN = 0000

SETUP Unlocked -

The SETUP button is unlocked, or has not been set for

the first time and the SETUP menus are accessible.
When entering the menu if the PIN has not been set, “PIN = 0000” with the

first “0” flashing will be displayed. When “PIN = 0000” is displayed, press

the Select knob. The first “0” will be flashing, rotate the Select knob to the

desired number 0-9 and press Select. Continue to set the remaining 3 digits

until the desired PIN number is displayed. After pushing the Select for the

last digit, the PIN is set and “Unlock SETUP <” is displayed.
When “PIN = 0***” is displayed a PIN has been entered, and the correct PIN

must be entered in order to access the 05 SETUP PIN and SETUP buttons. If

the incorrect PIN number is entered, “Invalid PIN” will be displayed. There is no

limit on how many attempts can be made to enter the correct PIN number.
To enter the correct PIN number rotate the Select knob to the correct digit

and then press Select. Continue to set the remaining 3 digits until the correct

PIN number is entered. After pushing the Select for the last digit “Unlock

SETUP <” will be displayed.

•

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды