Magnum Energy ME-ARC Скачать руководство пользователя

Страница: 44 / 63

5.0 Operation

5.2 Operating the Inverter/Charger

5.2.1 Inverter Mode
Turning the inverter on:

Press the ON/OFF INVERTER button to activate

the inverter function. The inverter will either be actively “Inverting” by using

power from the batteries to power the AC loads (see Figure 5-4); or will be

“Searching” for a load by using very little power from the batteries, if in Search

mode (see Figure 5-3). The green ‘INV’ LED will be on when the inverter is

actively Inverting and the green ‘INV’ LED will

ash while searching.

Turning the inverter off:

While the inverter is actively “Inverting” or “Search-

ing”, the ON/OFF INVERTER button can be pressed to switch the inverter

function off, and this will turn the green ‘INV’ LED off (see Figure 5-2).

Inverter Standby:

The inverter is in standby when the inverter is active

(green ‘INV’ LED is on) and an external AC power (utility/shore or generator) is

passing through the inverter to power the AC loads. During normal operation,

the AC loads will be powered by the external AC power, however, if a blackout

or brownout condition occurs, the inverter senses these conditions, transfers

to inverter mode and powers the AC loads connected to the inverter.

CAUTION:

If you have critical loads and are in Inverter Standby, do

not press the ON/OFF INVERTER button to turn the inverter function

off. If the green ‘INV’ LED is off, inverter power will NOT be available

to run your critical loads if the external AC power is interrupted.

5.2.2 Charger Mode
Turning the Charger on:

The charger will automatically be activated and

begin to charge your batteries when acceptable AC power (utility or genera-

tor) is connected to the input (HOT IN 1) of the inverter. When the charger

is ON, it produces DC voltage and current to charge your batteries. The CHG

LED will be solid when the charger is ON and actively charging. While charg-

ing the display will show Bulk, Absorption, Float, Full charge or Silent (see

Figures 5-5 thru 5-9).

Charger Standby:

While the charger is actively charging, the ON/OFF CHAR-

GER button can be pressed to switch the charger to “Charger Standby”. While

in Charger Standby, the incoming AC is still available on the inverter’s out-

put, but the charger is not allowed to charge. The display will show ‘Charger

Standby’ and the CHG LED will

ash (see Figure 5-10).

Info:

To resume charging, momentarily press the ON/OFF CHARGER

button; or disconnect/reconnect AC power to the inverter’s input.

Equalize charging:

Equalizing is a “controlled over charge” performed after

the batteries have been fully charged. It helps to mix the battery electrolyte

(to reverse the buildup of strati

cation), and also helps to remove sulfates

that may have built up on the plates. These conditions, if left unchecked will

reduce the overall capacity of the battery.

WARNING:

Do not perform an Equalization charge without reading

and following all safety precautions pertaining to charging/equaliza-

tion as noted in this manual, and any equalization information in

the inverter’s manual.

To enable the Equalization charge; see Figure 5-11 and follow all related

information on page 46.

http://www.wholesalesolar.com/inverter_systems.html

Содержание ME-ARC
































































Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC, Руководство пользователя

Результаты поиска

Содержание ME-ARC

Отзывы:

Похожие инструкции для ME-ARC

Бренды по названию

Популярные бренды