M-system 47DAC Скачать руководство пользователя | Manualshive

Страница: 111 / 251

background image

111

47DAC OPERATING MANUAL EM-9518-B Rev.4

9.8 ALARM OUTPUT LOGIC

(coil energized or de-energized at alarm)

Alarm output logic can be selected.  This parameter is called energizing direction and coil energized ‘EN’ or de-energized
‘DE’ at alarm can be selected. In selecting coil de-energized at alarm, the alarm output logic is inverted.  The default set-
ting is coil energized.  The coil at alarm is configurable also for the P status.

NOTE

Even when this setting is changed, operation of the alarm indicators is not reversed.

9.8.1 OPERATING PROCEDURE

NOTE

The following figures are display examples. The displays
depend on the settings.

1

Hold down Alarm/

↓

button for 3 seconds or more to move on

to Alarm Setting Mode.

• The alarm output pattern is indicated.
• The SD indicates ‘ALM PTN’.

NOTE

With the bank switching set to “enabled via the front button control”, the bank No. is indicated (‘ALM BNK’ on the SD).

2

Press Alarm/

↓

or Scale/

↑

button to go to the LL (L, H, HH or P)

coil at alarm setting.

• The LL (L, H, HH or P) coil at alarm is indicated.
• The SD indicates ‘RELAYLL’ (‘RELAY L’, ‘RELAY H’, ‘RELAYHH’ or

‘RELAY P’).

• ‘LL’ (‘L’, ‘H’, ‘HH’ or ‘P’) indicator starts blinking.

3

Press Shift and Up buttons to select the LL (L, H, HH or P) coil

at alarm.

• Select ‘EN’ or ‘DE’.

1,2,

4

2,4

3

3

Blinking

Blinking

Blinking

«
...
109
110
111
112
113
...
»

Содержание 47DAC




























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47DAC

Бренд: janitza Страницы: 28

Бренд: Callaway Страницы: 13

Бренд: Halcyon Страницы: 36

Бренд: Oakton Страницы: 4

Бренд: ColorLite Страницы: 68

Бренд: Vectronics Страницы: 4

Бренд: Omega Страницы: 31

Бренд: Feature tech Страницы: 2

Бренд: Dakota Digital Страницы: 38

Бренд: Swema Страницы: 4

Бренд: A&D Страницы: 2

Бренд: AXE Страницы: 5

VACTEST GCD 200

Бренд: BUSCH Страницы: 12

Бренд: Westfalia Страницы: 2

A570 Ambient Monitor

Бренд: iDigit Страницы: 15

Бренд: Geokon Страницы: 19

Бренд: Rayleigh Instruments Страницы: 6

NomaSense CO2 P2000

Бренд: NOMACORC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды