M-system 47DAC Скачать руководство пользователя

Страница: 88 / 251

47DAC OPERATING MANUAL EM-9518-B Rev.4

8.2 ANALOG OUTPUT FUNCTION MODE

8.2.1 OPERATING PROCEDURE

NOTE

The following figures are display examples. The displays
depend on the specifications and settings.

Hold down Scale/

↑

button for 3 seconds or more to move on to

Scaling Setting Mode.

• The input type is indicated.
• The SD indicates ‘INTYPE’.

Press Alarm/

↓

or Scale/

↑

button to go to the analog output

function mode setting.

• The analog output function mode is indicated.
• The SD indicates ‘ANG VAL’.

Press Shift and Up buttons to select the analog output func-

tion mode.

• Select ‘DISPLY’ or ‘SCALE’.

Press Alarm/

↓

or Scale/

↑

button to apply the new setting.

• And the next parameter setting is indicated.

NOTE

• Press Alarm/

↓

button, and the analog output 0% will be indicated (‘ANG L’ on the SD).

• Press Scale/

↑

button, and the analog output type will be indicated (‘ANG TYP’ on the SD)..

2,4

1,2,

Blinking

Содержание 47DAC




























































































































































































































































Результаты поиска

Содержание 47DAC

Отзывы:

Похожие инструкции для 47DAC

Бренды по названию

Популярные бренды

M-system 47DAC, Руководство по эксплуатации

Результаты поиска

Содержание 47DAC

Отзывы:

Похожие инструкции для 47DAC

Бренды по названию

Популярные бренды