M-system 47DAC Скачать руководство пользователя | Manualshive

Страница: 100 / 251

background image

100

47DAC OPERATING MANUAL EM-9518-B Rev.4

4

Press Alarm/

↓

or Scale/

↑

button to apply the new setting.

• And the next parameter setting is indicated.

NOTE

• Press Alarm/

↓

button, and the L (H or HH) alarm setpoint (‘ALARM L’, ‘ALARM H’ or ‘ALARMHH’ on the SD), or the

display blinking at alarm (‘ALMBLNK’ on the SD) will be indicated. Or the LL (L, H or HH) trip action will be indicated
(‘LIMT LL’, ‘LIMT L’, ‘LIMT H’ or ‘LIMT HH’ on the SD) with the alarm setting lockout set to “completely unlock Alarm Set-
ting Mode”.

• Press Scale/

↑

button, and the alarm output pattern (‘ALM PTN’ on the SD), or the LL (L or H) setpoint (‘ALARMLL’,

‘ALARM L’ or ‘ALARM H’ on the SD) will be indicated. Or the alarm output pattern (‘ALM PTN’ on the SD) or the LL (L
or H) coil at alarm (‘RELAYLL’, ‘RELAY L’ or ‘RELAY H’ on the SD) will be indicated with the alarm setting lockout set to
“completely unlock Alarm Setting Mode”.

5

■

TO GO ON TO SET ANOTHER ALARM SETPOINTS,

Repeat operation from Step 2.

■

TO SET THE NEXT PARAMETER,

Skip to Step 2 in “9.3 TRIP ACTION (LO/HI)”.

■

TO QUIT,

Hold down Alarm/

↓

or Scale/

↑

button for 1 second or more to return to Measuring Mode.

«
...
98
99
100
101
102
...
»

Содержание 47DAC




























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 47DAC

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Network Card-MS

Бренд: Eaton Страницы: 26

Бренд: Xylem Страницы: 19

Бренд: Topcon Страницы: 62

Бренд: Cecomp Страницы: 4

Бренд: Polimaster Страницы: 6

Бренд: STONEX Страницы: 99

Бренд: PITSID Страницы: 22

Бренд: Swan Analytical Instruments Страницы: 102

Microlog GX Series

Бренд: SKF Страницы: 342

WD-35606-00, WD-35606-05

Бренд: Oakton Страницы: 10

Бренд: Fuji Electric Страницы: 85

Бренд: Bitzer Страницы: 8

Бренд: IFM Страницы: 17

Бренд: Chauvin Arnoux Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды