M-system 47DAC Скачать руководство пользователя страница 77

Страница: 77 / 251

47DAC OPERATING MANUAL EM-9518-B Rev.4

(5) Parameter shifting in Infrared Communication Mode

There is no parameter shifting in this mode.

(6) Parameter shifting in Lockout Setting Mode

In Lockout Setting Mode, pressing Alarm/

↓

button shifts one parameter to the next (clockwise in the following figure).

Pressing Scale/

↑

button shifts one to the previous (counterclockwise).

NOTE

• The display depends on the specifications and settings. The above displays show default values.
• Hold down Alarm/

↓

or Scale/

↑

button for 1 second or more to return to Measuring Mode from each parameter.

(7) Parameter shifting in Loop Test Output Mode

There is no parameter shifting in this mode.

Measuring Mode

Scaling setting lockout

Advanced setting lockout

Forced zero control (Up button) lockout

Initialization

at once for a preset time duration

Hold down Max/Min + Alarm/

↓

1 Enabled with the I/O option code ‘4’ , ‘7’ or ‘8’ (network interface).

Alarm setting lockout

Loop test output lockout

Modbus setting lockout

Lockout Setting Mode

MAX/MIN display control

lockout

IR communication lockout

Modbus communication lockout

Содержание 47DAC




























































































































































































































































Результаты поиска

Содержание 47DAC

Отзывы:

Похожие инструкции для 47DAC

Бренды по названию

Популярные бренды

M-system 47DAC, Руководство по эксплуатации

Результаты поиска

Содержание 47DAC

Отзывы:

Похожие инструкции для 47DAC

Бренды по названию

Популярные бренды