Lucent Technologies MERLIN LEGEND Release 5.0 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 869

Lucent Technologies MERLIN LEGEND Release 5.0 Скачать руководство пользователя страница 98

MERLIN LEGEND Communications System Release 5.0
Feature Reference

555-650-110

Issue 1

June 1997

Features

Page 66

Automatic Route Selection

A table contains some or all of the following types of information:

■

Table Type. Indicates how to interpret the information in the table. Table
types are Area Code, Local Exchange, 6-Digit, 1 + 7, Dial 0, Special
Numbers (N11), Default Toll, and Default Local. Details for each table type
are discussed later in this section.

■

Digit Strings. Table includes 3-digit entries, usually area codes or
exchanges. Dialed digits are compared to the stored digits. A match should
occur in only one table and cause selection of the routes in that table.

■

Subpattern. An array of up to six routes. There are two subpatterns for all
tables except the Special Numbers (N11) and Dial 0 tables. The subpattern
selected depends on the time of day that the call is made and the start time
associated with each subpattern. (The start time for Subpattern A is
specified as the stop time for Subpattern B.)

The Special Numbers (N11) Table always uses the main pool and thus has
neither subpatterns nor routes. The Dial 0 Table has no subpatterns and
only one route.

■

Routes. A structure that defines possible lines/trunks to be used in a
preferred order, usually based on lowest cost and the extension user’s
privilege level or Facility Restriction Level (FRL). Routes cannot be
programmed for the Special Numbers (N11) Table. A route contains the
following types of information.

— Pool. A group of lines/trunks that are to be used for this route. A pool

must be programmed before any other route information.

NOTE:

If you are using data in your system, program pools, including the
default pool, for the proper data type. For example, a pool with T1
data-only lines cannot be used for voice calls. Loop-start,
ground-start, T1 voice, and some PRI lines support only voice
calls, while BRI lines and other PRI lines support both voice and
data calls.

— Facility Restriction Level (FRL). A value from 0 to 6 associated with

the route. For routes, 0 is the least restrictive and 6 the most restrictive
value. In order to use a route, a caller (according to extension or remote
access barrier code/trunk) must have an FRL that is equal to or greater
than the FRL of the route.

— Absorbed Digits. The number (0–11) of user-dialed digits that ARS

absorbs (does

not

dial out) on this route. Digits are absorbed starting

with the first user-dialed digit, after any leading star codes.

— System-Prefixed Digits. A string of up to 20 digits (0–9, *, and Pause)

that ARS dials out on this route

before

dialing any remaining user-dialed

digits but after dialing any user-dialed leading star codes.

«
...
96
97
98
99
100
...
»

Содержание MERLIN LEGEND Release 5.0






































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды