LPKF ProtoMat C 30-S Скачать руководство пользователя страница 55

Страница: 55 / 72

Appendix

ProtoMat C30/C30-S

13.4 SerialPort2 serial connection

The SerialPort2data channel is an RS 232-C standard port and can be

used for communication between the control unit and another system.

The SerialPort2 data transmission rate is programmed using DIL

switches 3 and 4.

SerialPort2 pinouts:

Any pin not mentioned is not used.

13.5 Connecting the stepping motors

The stepping motors are connected on each axis using a 15-pin SUB-D

connector. If a limit switch is actuated, any further axis movement

towards

the limit switch is immediately blocked.

The position of the sockets is described in the section entitled

"LPKF ProtoMat 91S displays and connections".

Caution! Never confuse the cable for the stepping motor and the

plotter head.

13.6 Connecting the plotter head

The plotter head is connected to the control unit with a 15-pin socket.

The position of the socket is described in the section entitled "LPKF

ProtoMat 91S displays and connections".

A further 5-pin cable supplies the plotter spindle.

Caution! Never confuse the cable for the stepping motor and the

plotter head.

Switch 3

Switch 4

Baud rate

OFF

4800 baud

OFF

9600 baud Default setting

OFF

PIN

Signal

Meaning

TXD

Transmit Data

RXD

Receive Data

RTS

Request to Send

CTS

Clear to Send

GND

Ground

Содержание ProtoMat C 30-S









































































Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды

LPKF ProtoMat C 30-S, Руководство пользователя

Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды