LPKF ProtoMat C 30-S Скачать руководство пользователя страница 57

Страница: 57 / 72

Appendix

ProtoMat C30/C30-S

13.9 Removing the electronics unit

The control unit must be isolated from the mechanism.

First move the plotter head to the

TOOL CHANGE

position if the plotter

head is still attached. Now use the arrow buttons to move the crossbar to

the centre of the machine base plate.

Caution! The head must not be in either the TOOL CHANGE or

Home position and the limit switches must have been cleared.

Switch off the circuit board plotter and disconnect the device from the

mains by removing the mains connector.

fig. 38: Position of screws for

removing the electronics
unit from the mechanism

› Undo the electric connections between the mechanism and the

control unit. Tilt the circuit-board plotter towards the head.

› Undo feet 1, 2, 3, 4 and the Allen screws 5, 6 on the underside of the

machine. Remove the cover with the limit switches. The control unit

has now been released.

Caution! Check that the machine is disconnected from the mains

by removing the mains connector.

K ippen

Содержание ProtoMat C 30-S









































































Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды

LPKF ProtoMat C 30-S, Руководство пользователя

Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды