LPKF ProtoMat C 30-S Скачать руководство пользователя страница 40

Страница: 40 / 72

Procedures for milling and drilling

40 ProtoMat C30/C30-S

10.5 Drilling

fig. 23: Twist drill

Caution! Make sure that the board is secured in position before

drilling. Switch on the vacuum system.

The boards must be drilled with drills designed specifically for boards. It

is important that the head always lowers at a constant speed. This is

ensured by a damper built into the plotter head.

Lowering the head too quickly may result in burring, particularly with

holes of small diameter. We therefore recommend that you punch holes

with a small diameter before drilling. The

MARKINGDRILLS

phase in

BoardMaster

is intended for this purpose and uses a special universal

milling cutter, the

0.2 MM UNIVERSAL MARKING CUTTER

Only one board can be drilled at a time. It is not possible to stack boards

one on top of the other. A drill cover plate is not required.

All drills are 38 mm long.

See the section entitled “Practical tips” for further instructions.

10.6 Isolation milling

fig. 24: LPKF Universal (1) and

microcutters (2)

Caution! Make sure that the board is positioned securely before

milling. Switch on the vacuum system.

Ensure that the (36 mm long)

LPKF universal milling cutters

being used

are

sufficiently sharp

before you start milling. The milling width is

preset in

CircuitCAM

by selecting the isolation track width and the

appropriate tool. The preferred milling width is between 0.2 and 0.4 mm.

Содержание ProtoMat C 30-S









































































Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды

LPKF ProtoMat C 30-S, Руководство пользователя

Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды