LPKF ProtoMat C 30-S Скачать руководство пользователя страница 56

Страница: 56 / 72

Appendix

56 ProtoMat C30/C30-S

13.7 EPROMs

The software for the control unit is held on two EPROMs.

The LPKF

ProtoMat C30 (C30/S)

must be partially dismantled if the

EPROMs need to be replaced.

Proceed as described under "Removing the electronics unit".

Use only an PLCC pliers to remove the EPROMs as otherwise the

mounting contacts might be damaged.

Support the board from below when inserting new EPROMs to avoid

bending the board. Take care that the orientation of the EPROMs is

correct.

13.8 Switching the device voltage,

electrical fuses

Danger! Make sure that the mains connector is removed before

working on the fuses or opening the device.

The primary and secondary voltages on the LPKF ProtoMat C30 (C30/S)

are fused. The mains (primary) fuses are in the control unit power

connection and can be accessed from the outside.

Caution! Make sure that

both

fuses are replaced when switching to

another line voltage. Both fuses must have the

same

rating.

fig. 37: Setting the voltage and

fuses

The secondary fuses are inside the control unit.

The control unit must be removed from the mechanism before replacing

the fuses. Proceed as described under "Removing the electronics unit".

Содержание ProtoMat C 30-S









































































Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды

LPKF ProtoMat C 30-S, Руководство пользователя

Результаты поиска

Содержание ProtoMat C 30-S

Отзывы:

Похожие инструкции для ProtoMat C 30-S

Бренды по названию

Популярные бренды