manualshive.com logo in svg

Lakeshore 340, Руководство пользователя, Страница: 98 / 178

Поделиться
Скачать
Lakeshore 340 Скачать руководство пользователя страница 98

Lake Shore Model 340 Temperature Controller User’s Manual 

 

 

8-16 

Instrument Programming 

8.4.2  Reading From A Data Card 

To read a data card, place the card into the slot, then 

press the 

DataCard

 Key. The 

Identifying Card...

 

message is displayed, followed by the 

DATACARD

 

screen. Press the 

Next Setting

 key until 

Read DataCard

 

is highlighted. 

Once 

Read DataCard

 is highlighted, press the 

Enter

 

key. 

Use the 

Next Setting

 or 

Previous Setting

 key to select 

which type of information is to be read from the data 
card. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

8.4.3  Writing To A Data Card 

To write to a data card, place the card into the slot, 

then press the 

DataCard

 Key. The 

Identifying Card...

 

message is displayed, followed by the 

DATACARD

 

screen. Press the 

Next Setting

 key until 

Write 

DataCard

 is highlighted. Press the 

Enter

 key. 

Use the 

Next Setting

 or 

Previous Setting

 key to 

select which type of information is to be written to the 
data card. 
 
 
 
 

8.4.4  Erasing A Data Card 

To erase a data card, place the card into the slot, then press the 

DataCard

 Key. The 

Identifying Card...

 

message is displayed, followed by the 

DATACARD

 screen. Press the 

Next Setting

 key until 

Erase DataCard

 

is highlighted. Press the 

Enter

 key. The message 

Press SAVE SCREEN to continue, CANCEL SCREEN to 

abort

 is displayed. If you press the 

Save Screen

 key, the data card is erased. If you press the 

Cancel 

Screen

 key, the erasure is canceled. 

 
 

D a ta   L o g g in g

R e a d   D a ta C a r d
W r ite   D a t a C a r d

E r a s e   D a ta C a r d

C a r d :  12 8 K B   F la s h ,  M 3 4 0   C o n f ig

D A T A C A R D

C o n f ig u r a tio n
S e ttin g s
P r o g r a m s
U s e r   C u r v e s

C a lC u r v e s
M 3 4 0   M a in   C o d e

C a r d :  12 8 K B   F la s h ,  M 3 4 0   C o n f ig

R E A D   D A T A C A R D

Configuration 

Reads configuration, programs, and curves 
from the data card, saves user curves, then 
resets the Model 340 to the new 
configuration. 

Settings 

Reads the settings from the data card and 
resets the Model 340. 

Programs 

Reads the programs from the data card and 
reset the Model 340. The programs may then 
be accessed by pressing the 

Program

 key. 

User Curves 

Reads the user curves from the data card and 
saves the curves to memory. Press 

Curve 

Entry

 to access the curves. 

CalCurves 

Reads the selected CalCurve from the data 
card. Select the CalCurve from the data card 
and the curve location in the Model 340. 

M340 Main Code 

Reads the Model 340 Main Code from the 
data card and resets the Model 340. Used to 
receive factory software updates. 

C o n f ig u r a tio n
C a l  C u r v e s

M 3 4 0   M a in   C o d e

C a r d :  12 8 K B   F la s h ,  M 3 4 0   C o n f ig

W R IT E   D A T A C A R D

 

Configuration 

Writes the configuration, programs, and curves 
to data card. 

CalCurves 

Writes the selected CalCurve to the data card. 
Write as many individual curves to the data 
card as there is room in card memory. 

M340 Main Code 

A data card required to copy the Model 340 
Main Code. 

Содержание 340



















































































































































































Отзывы:

Нет отзывов