Lakeshore 340 Скачать руководство пользователя страница 129

Страница: 129 / 178

Lake Shore Model 340 Temperature Controller User’s Manual

Remote Operation

9-31

DFLT

Set To Factory Defaults

Input: DFLT

Returned:

Nothing

Remarks:

Sets all configuration values to factory defaults and resets the instrument. The

is required

to prevent accidentally setting the unit to defaults. May take some time; use the

BUSY?

command to determine completion.

DIOST?

Query Digital Input/Output Status

Input: DIOST?
Returned: <input bit weighting>, <output bit weighting>

Format:

nnn,nnn[term]

Remarks:

Returns the status of the digital input and output in bit weighting format.

DISPFLD

Configure

Displayed

Field

Input:

DSPFLD <field>, [<input>], [<source>]

Returned:

Nothing

Remarks:

Configures the displayed field.

<field>

Specifies field to configure. Valid entries:

<input>

Specifies input to display in the field.

< source>

Specifies input data to display. Valid entries:

= kelvin,

= Celsius,

= sensor units,

= linear data,

= minimum data, and

= maximum data.

Example: DSPFLD 2, A, 1[term] -

Displays kelvin reading for Input A in display field 2.

DISPFLD?

Query

Displayed

Field

Input: DISPFLD?

<field>

Returned: <input>, <data source>

Format:

ann,n[term]

Remarks:

Returns the parameters for a displayed field. See the

DISPFLD

command for parameter

descriptions.

<field>

specifies which field to query. Valid entries:

DISPLAY

Configure Main Display Parameters

Input:

DISPLAY [<number of fields>], [<contrast>], [<backlight enable>]

Returned:

Nothing

Remarks:

Configures the main display screen.

<number of fields>

Specifies how many input fields to display.

<contrast>

Specifies the display contrast percentage.

<backlight enable>

Disables or enables the display backlight.

Example: DISPLAY 3, 60[term] -

Displays 3 input fields and sets the contrast to 60%.

DISPLAY?

Query Main Display Parameters

Input: DISPLAY?
Returned: <number of fields>, <contrast>, <backlight enable>

Format:

n,nnn,n[term]

Remarks:

Returns main display parameters. See the

DISPLAY

command for parameter descriptions.

DOUT

Configure Digital Output Parameters

Input:

DOUT [<mode>], [<bit weighting>]

Returned:

Nothing

Remarks:

Configures the parameters of the digital output.

<mode>

Specifies the mode of the digital output. Valid entries:

= off,

= alarms,

= scanner, and

= manual.

<bit weighting>

Specifies the manual digital output settings if

<mode>

Example: DOUT 3, 21[term] -

Manually sets digital output lines D1, D3, and D5 to logic high, and D2

and D4 to logic low.

Содержание 340



















































































































































































Результаты поиска

Содержание 340

Отзывы:

Lakeshore 340, Руководство пользователя, Страница: 129 / 178

Результаты поиска

Содержание 340

Отзывы: