Lakeshore 340 Скачать руководство пользователя страница 123

Страница: 123 / 178

Lake Shore Model 340 Temperature Controller User’s Manual

Remote Operation

9-25

TST?

Query

Self-Test

Input: *TST?
Returned: 0

Format:

n[term]

Remarks:

The Model 340 performs a self-test at power-up.

= no errors found,

= errors found.

WAI

Wait-to-Continue

Input: *WAI
Returned:

Nothing

Remarks:

This command is not supported in the Model 340.

ALARM

Configure Input Alarm Parameters

Input:

ALARM <input>, [<off/on>], [<source>], [<high value>], [<low value>],
[<latch enable>], [<relay>]

Returned:

Nothing

Remarks:

Configures the alarm parameters for an input.

<input>

Specifies which input to configure.

<off/on>

Determines whether the instrument checks the alarm for this input.

<source>

Specifies input data to check. Valid entries:

= kelvin,

= Celsius,

= sensor units,

= linear data.

<high value>

Sets the value the source is checked against to activate the high alarm.

<low value>

Sets the value the source is checked against to activate low alarm.

<latch enable>

Specifies a latched alarm (remains active after alarm condition correction).

<relay enable>

Specifies how the activated alarm affects relays.

NOTE:

Does not

guarantee the alarm activates the relays. See the

RELAY

command.

Example: ALARM A, 0[term] -

Turns off alarm checking for Input A.

ALARM B, 1, 1, 270.0, ,1[term] -

Turns on alarm checking for input B, activates high alarm if

kelvin reading is over 270, and latches the alarm when kelvin reading falls below 270.

ALARM?

Query Input Alarm Parameters

Input: ALARM?

<input>

Returned: <off/on>, <source>, <high value>, <low value>, <latch enable>, <relay enable>

Format:

n,n,

nnn.nnnE

n,n,n[term]

Remarks:

Returns the alarm parameters of an input. See the

ALARM

command for parameter

descriptions.

<input>

specifies which input to query.

ALARMST?

Query Input Alarm Status

Input: ALARMST?

<input>

Returned: <high status>, <low status>

Format:

n,n[term]

Remarks:

Returns the alarm status of an input.

<input>

specifies which input to query.

ALMRST

Clear Alarm Status for All Inputs

Input: ALMRST
Returned:

Nothing

Remarks:

Clears both the high and low status of all alarms, including latching alarms.

Содержание 340



















































































































































































Результаты поиска

Содержание 340

Отзывы:

Lakeshore 340, Руководство пользователя, Страница: 123 / 178

Результаты поиска

Содержание 340

Отзывы: