manualshive.com logo in svg

Lakeshore 340, Руководство пользователя, Страница: 96 / 178

Поделиться
Скачать
Lakeshore 340 Скачать руководство пользователя страница 96

Lake Shore Model 340 Temperature Controller User’s Manual 

 

 

8-14 

Instrument Programming 

8.4.1.1 Log Setup 

To setup the data log, highlight 

Setup data log

 and 

press the 

Enter

 key. The 

SETUP DATA LOG

 screen 

appears. 
 
 
 
 

Every

 

Sets the interval for storing records as one record every 1 to 3600 readings or one 
record every 1 to 3600 seconds. The interval number is set first followed by units. 

readings/seconds

 

Selects the unit of the logging rate. Every 20 readings equals 1 second, because the 
Model 340 updates the readings 20 times a second. 

Start Mode

 Selecting 

Clear

 clears old records before starting data logging. Selecting 

Continue

 

continues data logging and adds new records to existing data. 

Overwrite

 

Yes

:  Data logging continues beyond the maximum number of records specified and 

overwrites old records with new. 

 No

:  Data logging stops at the maximum number of records specified. 

Type

 

Specifies the data type of the specified 

Point

. Five data types are available to log: 

(1) Input 

reading 

(2)  SP1 (Setpoint of Control Loop 1) 
(3)  SP2 (Setpoint of Control Loop 2) 
(4)  Out1 (Output of Control Loop 1) 
(5)  Out2 (Output of Control Loop 2) 
If no data logging is necessary for the specified 

Point

, select 

None

. 

Note

: Changing 

Type

 will erase stored records. 

Input

 

Specifies Input channel to log. This field is available only if 

Input

 is specified in the 

Type

 field. 

Note

: Changing 

Input

 will erase stored records. 

Source

 

Specifies the source of the selected Input channel. TEMP K, TEMP C, MAX, MIN, 
SENSOR, LINEAR can be chosen. This field is available only if 

Input

 is specified in the 

Type

 field. 

Note

: Changing 

Source

 will erase stored records. 

8.4.1.2 Starting Data Logging 

To start data logging, highlight 

Start logging data

 and press the 

Enter

 key. The data logging starts 

immediately and the 

Status

 on the right bottom of the 

DATA LOGGING 

screen will indicate 

Logging

. The 

Record

 counter on the left bottom of the same screen will increment as records are stored in the SRAM Data 

Card. 

NOTE:

  Data logging will not start if the Data Card is write protected, or it has full data and 

Continue

 is 

selected in the 

Start Mode

 with 

No Overwrite

. 

8.4.1.3  Stopping Data Logging 

To stop data logging, highlight 

Stop logging data

 and press the 

Enter

 key. The data logging stops 

immediately and the 

Status

 on the right bottom of the 

DATA LOGGING 

screen will indicate 

Stopped

. The 

Record

 counter on the left bottom of the same screen shows the number of records that are currently stored 

in the SRAM Data Card. 

             SETUP DATA LOG 

Every: 

   1

 readings      Overwrite: NO 

Start Mode: Continue

    

                Point Type  Input Source 

                1:    None 

                2:    None 
                3:    None 

                4:    None 

Содержание 340



















































































































































































Отзывы:

Нет отзывов