Lakeshore 340 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 178

Lakeshore 340 Скачать руководство пользователя страница 145

Lake Shore Model 340 Temperature Controller User’s Manual

Options and Accessories

10-5

10.3 MODEL 3462 DUAL STANDARD INPUT OPTION CARD

The Model 3462 Input Card adds two standard inputs to the Model 340 Temperature Controller. The inputs
appear as C & D on the display. The original standard inputs remain fully functional.

10.3.1 Field Installation

The Model 3462 Option kit adds two optional sensor inputs to the Model 340 instrument rear panel. It

includes:
• (1) 10-conductor

Ribbon

Cable

• (1) 3462

Option

Card

• (4) 1¼-inch metal standoffs

• (8) 4-40 machine screws

Required tools:

Small Phillips-head screwdriver and 5/64-inch Allen Wrench.

1. Turn Model 340 power switch OFF. Unplug power cord from wall outlet, then instrument.

2. Stand the unit on its face. Use the Allen wrench to remove the 4 screws on each side of the covers.

3. Use the small Phillips screwdriver to remove any top and bottom cover screws; instruments may have

1 or 2 screws on the top and bottom covers.

4. Remove rear plastic bezel. The covers are tracked. Slide the top and bottom covers to the rear on the

tracks to remove them.

5. Remove rear panel option plate screws and set aside. Remove rear panel option plate.

SIDE COVER

SCREWS

(On Both Sides)

REAR PLASTIC

BEZEL

TOP COVER SCREWS

(Remove bottom

cover screws also)

To remove top

and bottom

covers, slide

them to the rear

on the tracks.

DIGITAL I/O

ANALOG

OUT 1

ANALOG

OUT 2

SERIAL I/O

120

IEEE-488 INTERFACE

SH1 AH1 T5 L4 SR1 RL1 PP0 DC1 DT0 C0 E1

RELAYS

NC C NO NC C NO

LO

HI

HEATER FUSE

2.5 A

HEATER OUTPUT

LO

HI

DATA CARD

FUSE
DATA

-10% +5%
50-60 Hz
175 VA MAX

LINE

100 / 120
2.0 A
.25x1.25in SB

220 / 240
1.0 A
5x25mm SB

OFF

ON

INPUT A

l+

V+

l-

V-

INPUT B

l+

V+

l-

V-

60V MAX

WARNING

NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO TRAINED SERVICE PERSONNEL.

!

WARNING

FOR CONT5INUED PROTECTION AGAINST FIRE HAZARD,
REPLACE FUSE WITH SAME TYPE AND RATING.

!

EXT

REAR PANEL

OPTION PLATE SCREWS

OPTION PLATE

Figure 10-5. Cover and Option Plate Screws

«
...
143
144
145
146
147
...
»

Содержание 340



















































































































































































Отзывы:

Нет отзывов