manualshive.com logo in svg

Lakeshore 340, Руководство пользователя, Страница: 8 / 178

Поделиться
Скачать
Lakeshore 340 Скачать руководство пользователя страница 8

Lake Shore Model 340 Temperature Controller User’s Manual 

 

 

iv 

Table of Contents

 

TABLE OF CONTENTS (Continued) 

Chapter/Paragraph Title 

Page 

6.13 CONTROL 

OUTPUT LIMITS........................................................................................................... 6-11 

6.13.1 Setpoint Limit ............................................................................................................................... 6-11 
6.13.2 Control 

Output Slope Limit ........................................................................................................... 6-11 

6.13.3 Heater 

Range Limit ...................................................................................................................... 6-11 

7 

ANALOG OUTPUT, DIGITAL I/O. ALARMS, AND RELAY OPERATION ............................................................ 7-1 

7.0 GENERAL ......................................................................................................................................... 7-1 
7.1 ANALOG 

OUTPUTS.......................................................................................................................... 7-1 

7.1.1 

Input Mode for Analog Output ........................................................................................................ 7-2 

7.1.2 

Example of Low and High Parameter Setting ................................................................................ 7-2 

7.1.3 

Loop 2 Mode for Analog Output 2 .................................................................................................. 7-2 

7.1.4 

Manual Mode Operation of the Analog Outputs ............................................................................. 7-3 

7.2 DIGITAL 

INPUTS 

AND OUTPUTS (I/O)............................................................................................ 7-3 

7.2.1 Digital 

Output Modes...................................................................................................................... 7-3 

7.2.2 Digital 

Outputs in Alarm Mode ....................................................................................................... 7-3 

7.2.3 Digital 

Outputs in Scanner Mode.................................................................................................... 7-3 

7.2.4 Digital 

Outputs in Manual Mode ..................................................................................................... 7-4 

7.2.5 Digital 

Input Modes ........................................................................................................................ 7-4 

7.3 INPUT 

ALARMS ................................................................................................................................ 7-4 

7.3.1 Enabling 

an 

Input Alarm................................................................................................................. 7-4 

7.3.2 Selecting 

an 

Input Alarm Source.................................................................................................... 7-5 

7.3.3 

Input Alarm High and Low Settings ................................................................................................ 7-5 

7.3.4 Input 

Alarm Latching ...................................................................................................................... 7-5 

7.3.5 Input 

Alarm Relay Setup ................................................................................................................ 7-5 

7.3.6 Input 

Alarm Reset .......................................................................................................................... 7-6 

7.3.7 Audible Beeper............................................................................................................................... 7-6 
7.4 HIGH 

AND 

LOW RELAYS................................................................................................................. 7-6 

7.4.1 Selecting 

a Relay Mode ................................................................................................................. 7-6 

7.4.2 Manually 

Setting a Relay ............................................................................................................... 7-6 

8 INSTRUMENT 

PROGRAMMING............................................................................................................................ 8-1 

8.0 GENERAL ......................................................................................................................................... 8-1 
8.1 

CURVE ENTRY FROM THE FRONT PANEL ................................................................................... 8-1 

8.1.1 Curve 

Numbers and Storage ......................................................................................................... 8-1 

8.1.2 

Front Panel Curve Entry Operations .............................................................................................. 8-1 

8.1.3 Front 

Panel Curve Edit................................................................................................................... 8-2 

8.1.4 Front 

Panel Curve Copy................................................................................................................. 8-3 

8.1.5 Front 

Panel Curve Erase................................................................................................................ 8-3 

8.2 SOFTCAL™ ...................................................................................................................................... 8-4 
8.2.1 

SoftCal and Silicon Diode Sensors ................................................................................................ 8-4 

8.2.2 SoftCal 

Accuracy 

with Silicon Diode Sensors ................................................................................ 8-5 

8.2.3 

SoftCal and Platinum Sensors ....................................................................................................... 8-5 

8.2.4 SoftCal 

Accuracy 

with Platinum Sensors ....................................................................................... 8-5 

8.2.5 

Creating a SoftCal Calibration Curve ............................................................................................. 8-6 

8.3 INTERNAL 

PROGRAMMING ............................................................................................................ 8-6 

8.3.1 Program 

Instructions ...................................................................................................................... 8-6 

8.3.2 Internal 

Programming Operations ................................................................................................ 8-10 

8.3.3 

Enter or Edit an Internal Program................................................................................................. 8-10 

8.3.4 Saving a Program ........................................................................................................................ 8-11 
8.3.5 Summary 

of 

Key Operation.......................................................................................................... 8-11 

8.3.6 Example 

of 

an Internal Program (Example 1) .............................................................................. 8-11 

8.3.7 Example 

of 

Using Subprograms (Example 2) .............................................................................. 8-12 

8.3.8 

Run an Internal Program.............................................................................................................. 8-12 

8.3.9 

Stop a Running Program.............................................................................................................. 8-12 

8.3.10 Clear 

Internal Program Memory ................................................................................................... 8-13 

8.4 DATA 

CARD OPERATION.............................................................................................................. 8-13 

8.4.1 Data 

Logging 

To A Data Card...................................................................................................... 8-13 

8.4.2 Reading 

From A Data Card.......................................................................................................... 8-16 

8.4.3 Writing 

To A Data Card ................................................................................................................ 8-16 

8.4.4 Erasing 

A Data Card .................................................................................................................... 8-16

 

Содержание 340



















































































































































































Отзывы:

Нет отзывов