Lakeshore 340 Скачать руководство пользователя страница 53

Страница: 53 / 178

Lake Shore Model 340 Temperature Controller User’s Manual

Front Panel Operation

4-5

4.4.7 Key

Definitions

Key Description

AutoTune

Displays the

AUTO TUNE

screen to set Auto P, Auto PI, or Auto PID control mode.

Zone Settings

Displays the

ZONE SETTINGS

screen which specifies P, I, D, Manual Output, and

Heater Range for up to 10 Temperature control zones.

Ramp

Displays the

RAMP SETUP

screen which turns ramp on or off and selects ramp rate.

Program

Displays the

PROGRAM MODE

screen. Allows the user to Run an internal program,

Terminate a program, Edit a program, or Clear program memory.

Allows direct setting of the proportional (P) control parameter.

Allows direct setting of the integral (I) control parameter.

Allows direct setting of the derivative (D) control parameter.

Control Setup

Displays the

CONTROL SETUP

screen which enables the control loop, establishes

power up status and setpoint units, sets heater resistance and control mode, and turns

the filter on or off. Press the

More

key to display the

CONTROL LIMITS

screen which

sets the temperature, slope, maximum heater current, and range.

Heater Range

Allows direct setting of Loop 1 heater range.

Heater Off

Immediately turns off Loop 1 heater.

Control Channel

Allows direct setting of the sensor feedback channel for a control loop.

Loop 1

Displays Control Loop 1 parameters and status on lower three lines of display.

Loop 2

Displays Control Loop 2 parameters and status on lower three lines of display.

Setpoint

Allows direct setting of control setpoint.

Manual Output

Allows direct setting of manual output control parameter.

Input Setup

Displays the

INPUT SETUP

screen which selects the sensor type and curve number.

Other sensor parameters can be overwritten, but this changes sensor status to

"Special." Only curves appropriate to the sensor type display.

SoftCal

Displays the

SOFTCAL

screen which accepts and stores SoftCal curves.

Display Format

Displays three screens (use the

More

key to toggle between the screens):

1. The

READING DISPLAY FORMAT

screen sets the number of readings (1 thru 8)

shown in the normal display and assigns an input and data source to each.

2. The

CONTROL DISPLAY FORMAT

screen sets lower three lines of the display.

3. The

MISC. DISPLAY FORMAT

screen sets display contrast, back lighting, and

keypad lock.

Scan Setup

Displays the

EXTERNAL SCANNER SETUP

screen to set external scanner support.

Curve Entry

Displays the

CURVE ENTRY

screen which edits, copies, or erases temperature

response curves.

Interface

Displays the

COMPUTER INTERFACE

screen which sets IEEE-488.2 and Serial

interface parameters.

Alarm Setup

Displays the

ALARM SETTINGS

screen which enables or disables alarms and sets

various alarm parameters.

Math Setup

Displays the

MATH COMPUTATIONS

screen which sets Max/Min and Filter

parameters. Press the

More

key to see the

LINEAR EQUATION

screen.

Analog Outputs

Displays the

ANALOG OUTPUTS

screen which specifies Mode, Bipolar, Status, and

other parameters for Analog Output A and B.

Alarm Reset

Immediately resets all latched alarms.

Math Reset

Immediately resets all Max and Min values.

Options

Displays four screens:

1. The

DIGITAL I/O

screen manually sets the digital inputs and outputs.

2. The

RELAY & BEEPER SETUP

screen allows the user to choose alarm or manual

control for relays and to turn the beeper on or off.

3. The

DATE & TIME

screen is used to set real-time clock.

4. The

REVISION INFORMATION

screen displays the controller serial number and

revision history.

Use the

More

key to toggle between the screens.

Содержание 340



















































































































































































Результаты поиска

Содержание 340

Отзывы:

Lakeshore 340, Руководство пользователя, Страница: 53 / 178

Результаты поиска

Содержание 340

Отзывы: