Lakeshore 340 Скачать руководство пользователя страница 136

Страница: 136 / 178

Lake Shore Model 340 Temperature Controller User’s Manual

9-38

Remote Operation

MOUT?

Query Control Loop Manual Output Values

Input: MOUT?

<loop>

Returned: <manual output value>

. Format:

nnn.nn[term]

Remarks:

Returns the control loop manual output value.

<loop>

specifies which loop to query.

PGM

Add A Program Line

Input:

PGM <program>, <command>, [<param1>], [<param2>],...

Returned:

Nothing

Remarks:

Adds a command to a program. The command appends to the end of the specified program.
Each command has a different number of parameters and parameter formats. The
parameters are detailed under each command (Paragraph 8.3).

<command>

specifies the

command. End commands are ignored. Valid entries are:

- End: no parameters

- NOP: no parameters

- Repeat:

[<iterations>], [<infinite loop enable>]

- End Repeat: no parameters

- Wait:

[<hours>], [<minutes>], [<seconds>]

- Call:

[<program>]

- Ramp MOut Abs.:

[<MOut value>], [<hours>], [<minutes>], [<seconds>], [<rate value>]

- Ramp MOut Rel.:

[<deviation value>], [<hours>], [<minutes>], [<seconds>], [<rate>]

- Ramp SP Abs.:

[<SP value>], [<hours>], [<minutes>], [<seconds>], [<rate>]

- Ramp SP Rel.:

[<deviation value>], [<hours>], [<minutes>], [<seconds>], [<rate>]

- Parameters:

[<control channel>], [<control mode>], [<P value>], [<I value>], [<D value>],
[<heater range>]

- Digital Output:

[<bit weighting>]

- Relays:

[<high enable>], [<low enable>]

- Settle:

[<hours>], [<minutes>], [<seconds>], [<band>]

Example: PGM 1, 5, 2[term] -

Appends a Call command that calls program 2 to the end of program 1.

PGM?

Query A Program Line

Input:

PGM? <program>, <line>

Returned:

Variable. Format: variable

Remarks:

Returns the command and parameters for the specified program and line number. See the

PGM

command and Paragraph 8.3. Querying past the end of a program returns an End

command.

PGMDEL

Erase A Program

Input: PGMDEL

<program>

Returned:

Nothing

Remarks:

Erases a program.

<program>

specifies the program to erase. Valid entries:

Example: PGMDEL 2[term] -

Erases program 2.

PGMMEM?

Query Number of Program Lines Remaining

Input: PGMMEM?
Returned: <lines>

. Format:

nnn[term]

Remarks:

Returns the number of programs lines remaining in program memory.

PGMRUN

Run a Program.

Input: PGMRUN

<program>

Returned:

Nothing

Remarks:

Runs or terminates a program.

<program>

Specifies the program to run. Valid entries:

= terminate current program,

Example: PGMRUN 1[term] -

Begins execution of program 1.

Содержание 340



















































































































































































Результаты поиска

Содержание 340

Отзывы:

Lakeshore 340, Руководство пользователя, Страница: 136 / 178

Результаты поиска

Содержание 340

Отзывы: