Lakeshore 340 Скачать руководство пользователя страница 132

Страница: 132 / 178

Lake Shore Model 340 Temperature Controller User’s Manual

9-34

Remote Operation

<range>

Specifies the input range (refer to Paragraph 5.1.4). This parameter has a
predetermined value based on

<type>

. If this parameter is supplied,

<type>

changes to

(Special). Valid entries are (given in volts):

- 1 mV

- 10 mV

- 100 mV

- 1 V

- 7.5 V

- 2.5 mV

- 25 mV

- 250 mV

- 2.5 V

- 5 mV

- 50 mV

- 500 mV

- 5 V

Example: INTYPE A, 2[term] -

Sets Input A sensor type to GaAlAs diode.

INTYPE B, 3, , , 7[term] -

Sets Input B sensor type to Platinum 100, but use a 30 µV

excitation. Input B now responds as a Special.

INTYPE?

Query Input Type Parameters

Input: INTYPE?

<input>

Returned: <type>, <units>, <coefficient>, <excitation>, <range>

Format:

n,n,n,nn,nn[term]

Remarks:

Returns input type parameters. See the

INTYPE

command for parameter descriptions.

<input>

Specifies which input to query.

KEYST?

Query Keypad Status

Input: KEYST?
Returned: <keypad status>

Format:

n[term]

Remarks:

Returns keypad status since the last

KEYST?

= key pressed,

= no key pressed.

KEYST?

returns

after initial power-up.

KRDG?

Query Kelvin Reading for an Input

Input: KRDG?

<input>

Returned: <kelvin value>

Format:

nnn.nnnE

n[term]

Remarks:

Returns the kelvin reading for an input.

<input>

specifies which input to query.

LDAT?

Query Linear Equation Data for an Input

Input: LDAT?

<input>

Returned: <linear value>

Format:

nnn.nnnE

n[term]

Remarks:

Returns the linear equation data for an input.

<input>

specifies which input to query.

LDATST?

Query Linear Equation Data Status for an Input

Input: LDATST?

<input>

Returned:

A bit weighted integer from 0 - 255. Format:

nnn[term]

Remarks:

The integer returned represents the sum of the bit weighting of the input linear equation data
status flag bits.

<input>

specifies which input to query. See

RDGST?

Command.

LINEAR

Configure Input Linear Equation Parameters

Input:

LINEAR <input>, [<equation >], [<varM value>], [<X source>], [<B source>], [<varB
value>]

Returned:

Nothing

Remarks:

Configures the linear equation for an input.

<input>

Specifies input to configure.

<equation>

Specifies linear equation to use.

Valid

entries:

= (y = mx + b),

2 =

(y = m(x + b)).

<varM value>

Specifies a value for m in the equation.

<X source >

Specifies input data to use. Valid entries:

= kelvin,

= Celsius,

= sensor units.

<B source >

Specifies what to use for b in the equation. To use a setpoint, set its units to

the same type specified in

<X source>

. Valid entries:

= a value,

= +SP1,

= –SP1,

= +SP2,

= –SP2.

<varB value>

Specifies a value for b in the equation if

<B source>

is 1.

Example: LINEAR A, 1, 1.0, 1, 3[term] -

The linear data for Input A is calculated from the kelvin

reading of the input using the equation: y = 1.0 * × –SP1.

Содержание 340



















































































































































































Результаты поиска

Содержание 340

Отзывы:

Lakeshore 340, Руководство пользователя, Страница: 132 / 178

Результаты поиска

Содержание 340

Отзывы: