manualshive.com logo in svg

Lakeshore 340, Руководство пользователя, Страница: 61 / 178

Поделиться
Скачать
Lakeshore 340 Скачать руководство пользователя страница 61

Lake Shore Model 340 Temperature Controller User’s Manual 

 

 

Measurement Operation 

5-5 

 

Input

Processing

Conversion

to Temperature

Filter

PID

Control 

Linear

Equation

Maximum/

Minimum

Alarms

Hardware

Beeper

Relays

Display

Remote

Analog

Out

Heater

Out

OR

OR

OR

OR

V

Software

 

 

340-5-1.eps

 

 

Figure 5-1. Data Flow 

 

5.3.2 Max/Min 

The Model 340 will save the highest (Max) and lowest (Min) reading of a sensor input when the Max/Min 

feature is turned on. The feature can be paused to save these stored values after the observation period is 

over. A source for Max/Min must be selected on the math setup screen. There are four possible sources for 

the Max/Min feature. The input reading in sensor units, kelvin, Celsius, or the result of the linear equation can 

be chosen. Max/Min will work with one source for an input but different inputs can have different sources. Max 

and Min will not automatically show on the display. Use the Reading Display Format screen described in 

Paragraph 4.5 to show Max and Min on the display. 

To use the Max/Min feature, press the 

Math Setup

 key. The math setting screen will appear with the input 

letter in the top left hand corner. Use the 

s

 or 

t

 key to select an input. Press the 

Enter

 key or the 

Next 

Setting

 key to display the Max/Min parameters for that input. Press the 

Next Setting

 key until the Max/Min 

enable field is highlighted and then use 

s

 or 

t

 key to select on. Press the 

Next Setting

 key or the 

Enter

 key 

to advance to the source field. Use the 

s

 or 

t

 key to select one of the four sources. Press the 

Next Setting

 

key to make other changes. Press the 

Save Screen

 key to store the change in the Model 340. The default 

settings are On, kelvin. 

When the Max./Min feature is setup, it will not automatically appear on the display. Use the display format 

screen to add a reading field to the display and select the input and math source for that new field. Display 

format is discussed in Paragraph 4.5. 

To Pause the Max/Min feature, press the 

Math Setup

 key. The math setting screen will appear with the input 

letter in the top left hand corner. Use the 

s

 or 

t

 key to select an input. Press the 

Enter

 key or the 

Next 

Setting

 key to display the Max/Min parameters for that input. Press the 

Next Setting

 key until the Max/Min 

enable field is highlighted and then use 

s

 or 

t

 key to select pause. Press the 

Save Screen

 key to store the 

change in the Model 340. Changing back and fourth between on and pause will not reset the values. 

To reset the Max/Min values, press the 

Math Reset

 key from the normal display. Math reset is an immediate 

operation. 

Содержание 340



















































































































































































Отзывы:

Нет отзывов