Lakeshore 340 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 178

Lakeshore 340 Скачать руководство пользователя страница 64

Lake Shore Model 340 Temperature Controller User’s Manual

5-8

Measurement Operation

5.4.4 Auto

Scanning

Once the individual input channels are enabled and have a designated curve, the Auto Scan feature can

sequence through the enabled channels. A scan interval can be set by the user to tell the instrument how long

to read a channel before moving to the next. The interval is set in seconds and has a range of 2 to 200. The

Model 340 can set its digital outputs to the corresponding Auto Scan channel. If the external scanner has

digital control inputs the Model 340 can be used to select a channel. This is a convenient way to synchronize

the scanned readings or automate the scan operation using only Model 340.

To change the reading interval for the Auto Scan

mode, start with the scan mode set to Auto Scan.

Press the

Scan Setup

key and the scan setup

screen will appear. Press the

Next Setting

or

Previous Setting

key until the interval field is

highlighted. Use the

s

or

t

key to select the

appropriate scan interval in seconds. Press the

Save Screen

key to store the setting in the

Model 340. Please note that only input channels

that have been enabled on the input setup screen will be read in sequence. The default setting is 2.

The digital outputs must be set to scan mode to report the scan channel, refer to Paragraph 7.2 for digital
output mode setting. When the digital outputs are set to work with the scanner and Auto Scan mode selected,
digital output signals D1 to D4 report the active scan channel as shown in the table above.

5.4.5 Slave

Scanning

In some application it is necessary for the external
scanner or other external hardware to select the active
scan channel. In scanner slave mode the Model 340
will change to the active scan channel to the channel
indicated on the digital inputs. The digital inputs do not
need any special setup. The active scan channel will
follow the digital inputs as shown in the table below.
Digital input logic levels are described in Paragraph 7.2.

In t e r v a l:

M o d e :

2

s e c o n d s

A U T O S C A N

E X T E R N A L S C A N N E R S E T U P

Channel

DI4 DI3 DI2 DI1

1  0 0 0 0
2  0 0 0 1
3  0 0 1 0
4  0 0 1 1
5  0 1 0 0
6  0 1 0 1
7  0 1 1 0
8  0 1 1 1
9  1 0 0 0

10  1 0 0 1
11  1 0 1 0
12  1 1 1 1
13  1 1 0 0
14  1 1 0 1
15  1 1 1 0
16  1 1 1 1

«
...
62
63
64
65
66
...
»

Содержание 340



















































































































































































Отзывы:

Нет отзывов