Lakeshore 340 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 178

Lakeshore 340 Скачать руководство пользователя страница 141

Lake Shore Model 340 Temperature Controller User’s Manual

Options and Accessories

10-1

CHAPTER 10

OPTIONS AND ACCESSORIES

10.0 GENERAL

This chapter lists Model 340 Temperature Controller Options in Paragraph 10.1 and Accessories in
Paragraph 10.2. Further installation details of the Model 3462 Dual Standard Input Option Card are provided
in Paragraph 10.3, the Model 3464 Dual Thermocouple Input Option Card in Paragraph 10.4, the Model 3465
Single Capacitance Input Option Card in Paragraph 10.5, and the Model 3468 Eight-Channel Input Option
Card in Paragraph 10.6.

10.1 OPTIONS

Model

Description Of Model 340 Options

3462

Dual Standard Input Option Card.

Adds two standard inputs to the Model 340. The card has

separate A/Ds and excitation for each sensor. A microprocessor on the card manages the A/D and
communication with the Model 340. The card allows the Model 340 to read 4 sensors and use any
1 of the sensors as a control sensor. Includes these features:
• Standard inputs with the ability to select from the front panel to read the following sensors:

Diode, Platinum, Cernox, Rox, Germanium, Carbon-Glass, or any thermistor <30 k

Ω

.

• Adds two additional inputs each with its own excitation and A/D.
• Specifications match the Model 340 standard inputs.

3464

Dual Thermocouple Input Option Card.

Adds two thermocouple inputs to the Model 340. A

microprocessor on the card manages the A/D and communication with the Model 340.

3465

Single Capacitance Input Option Card.

Adds one capacitance input to the Model 340. A

microprocessor on the card manages the A/D and communication with the Model 340.

3468

Eight-Channel Input Option Card.

Adds eight additional inputs to the Model 340. Card has 2

Analog-to-Digital (A/D) Converters, one for each group of 4 sensors and individual excitation for
each sensor. A microprocessor on the card manages the A/D and communication with the Model
340. The card allows the Model 340 to read a total of 10 sensors. Includes the features below:
• Eight channels divided into 2 groups of 4. Several sensor types are supported.
• Eight individual current sources at 10

µ

A or 1 mA depending on sensor selection. Each sensor

is continuously excited.

• Two A/Ds; one for each group.

10.2 ACCESSORIES

Accessories are devices that perform a secondary duty as an aid or refinement to the primary unit.

Model

Description Of Model 340 Accessories

106-009

*

Heater Output Connector (Dual Banana Jack).

Used for standard Heater Output.

106-233

*

Sensor Mating Connector (Quantity 2).

6-pin DIN Plugs used for sensor inputs.

106-737

Terminal Block, 6-pin.

Used for Relays Connector. Accepts up to 12 AWG wire.

115-006

*

Detachable 120 VAC Line Cord.

* Accessories included with a new Model 340.

«
...
139
140
141
142
143
...
»

Содержание 340



















































































































































































Отзывы:

Нет отзывов