Lakeshore 340 Скачать руководство пользователя страница 66

Страница: 66 / 178

Lake Shore Model 340 Temperature Controller User’s Manual

6-2

Temperature Control Operation

6.1.4 Control Output Display

The Model 340 shows the control output value on the display so the operator can monitor the control loop

performance during an experiment or while tuning. The output value is shown on the display whenever loop

parameters for that loop are shown. Control output can also be shown on the display using large characters.

Refer to Paragraph 4.5 for display format.

If the message “Disabled” appears in the control output field of the display, the control loop must be enabled

from the

CONTROL SETUP

screen before it is operational, refer to Paragraph 6.2. (There is an enable

setting for each control loop and it is independent of heater range.)

Hardware included in the heater output circuit allows more features in monitoring and displaying control

output for Loop 1. If the correct value of heater resistance is entered, the heater output can be shown on the

display in power. To change heater output units, refer to Paragraph 4.5.6. The heater output is reported in

percent of full scale current or power for a given heater range. Full scale for the range is shown on the display

to indicate which range is selected. An A/D converter in the heater output circuitry also allows the Model 340

to diagnose problems in the heater circuit. If an error is detected, a message appears in the control output

field of the display. These errors are summarized in Paragraph 11.9. Error messages are not possible for

Loop 2. When Analog Output 2 is used for control output of Loop 2, the control output is reported in percent of

full scale output voltage.

6.2 CONTROL LOOP ENABLE

As a safety feature, both Control Loop 1 and 2 default to the disabled state. This state ensures that the heater

output for Loop 1 is off and Analog Output 2 for Loop 2 is set to zero volts. The user must enable a control

output before it can be used. If an output is disabled, the message Disabled appears in the control output field

of the display.

To enable or disable a control output, press the

Control Setup

key. The

CONTROL SETUP

screen is

displayed. The control loop indicator is highlighted in the upper left hand corner. Use

key to select

Loop 1 or 2. Press the

Enter

Next Setting

key. The control setup parameters for that loop appear on the

screen. Press the

Next Setting

key until the

Enable

field is highlighted. Use the

key to select

for

enabled or

OFF

for disabled. Press the

Enter

Next Setting

key to continue with more settings, or press the

Save Screen

key to store the changes in the Model 340. The default setting is Off.

Some systems require that a control output remains off if power is lost. The power up enable feature enables

the user to choose whether or not they want the control output to be disabled each time the instrument power

is turned off then on. Setting the power up parameter to off disables the control output on power up. Setting

the power up parameter to on enables the control output on power up.

To change the power up setting, press the

Control Setup

key. The

CONTROL SETUP

screen is displayed.

The control loop indicator is highlighted in the upper left hand corner. Use the

key to select Loop 1 or

2. Press the

Enter

Next Setting

key. The control setup parameters for that loop appear on the screen.

Press the

Next Setting

key until the

Power Up

field is highlighted. Use the

key to select on or off.

Press the

Enter

Next Setting

key to continue with more settings, or press the

Save Screen

key to store

the changes in the Model 340. The default setting is Off.

6.3 CONTROL LOOP FILTER

The control loop filter quiets feedback sensor noise that causes instability in the control loop. The control filter

works best on electrical noise from the environment or noise in temperature measurement. The control filter

can worsen control stability when unwanted disturbances exist in the load temperature because filtering

reduces the control loop bandwidth.

The control loop filter uses the same filter window and number of filter points as the input chosen as the

control channel. It can be turned on or off independently from the input filter.

To turn the control loop filter on or off, press

Control Setup

to display the

CONTROL SETUP

screen with the

control loop indicator highlighted in the upper left hand corner. Use the

key to select Loop 1 or 2.

Press

Enter

Next Setting

to display control setup parameters for that loop. Press

Next Setting

until the

Filtered

field highlights. Use the

key to select

OFF

. Press

Enter

Next Setting

to continue

with more settings, or press

Save Screen

to store changes in the Model 340. The default setting is Off.

Содержание 340



















































































































































































Результаты поиска

Содержание 340

Отзывы:

Lakeshore 340, Руководство пользователя, Страница: 66 / 178

Результаты поиска

Содержание 340

Отзывы: