Kustom Signals Digital Eyewitness HD Скачать руководство пользователя страница 6

Страница: 6 / 70

Digital Eyewitness

In-Car Video System

Manual Part Number:

006-1219-00 Rev. 0

Mini-Octopus (Mini-OTP) Cable (Part # 155-3952-00) ................................... 4-4

Accessory Cable (Part # 155-3956-25) .......................................................... 4-5

Installing the Power Cable (Part # 155-3957-25) ............................................ 4-7

Installing the Power Tamer ............................................................................. 4-8

5 Installation of GPS and Wi-Fi Antennas ..................................................... 5-1

General Information ........................................................................................ 5-1

Installing GPS Components (Part # 015-1599-00) ..................................... 5-1

Installing Wireless N File Transfer 5.0 GHz Antenna Components

(Part # 050-0860-00) ............................................................................... 5-2

6 Installation of the Digital Video Recorder (DVR) ....................................... 6-1

General Description ........................................................................................ 6-1

DVR Front Panel ......................................................................................... 6-1

DVR Rear Panel ......................................................................................... 6-2

DVR Heat Management ........................................................................................... 6-3

DVR / System Serial Number Locations ..................................................... 6-4

Preparing the DVR for Mounting ................................................................. 6-4

Mounting the DVR ....................................................................................... 6-4

7 Installation of the Mobile Data Computer (MDC) Option .......................... 7-1

General Description ........................................................................................ 7-1

Minimum System Requirements ................................................................. 7-1

Eyewitness

HD MDC Installation Instructions ........................................... 7-1

8 Field Verification of File Transfer Operability ............................................ 8-1

General Information ........................................................................................ 8-1

Index .......................................................................................................... Index-1

Содержание Digital Eyewitness HD







































































Результаты поиска

Содержание Digital Eyewitness HD

Отзывы:

Бренды по названию

Популярные бренды

Kustom Signals Digital Eyewitness HD, Руководство по установке

Результаты поиска

Содержание Digital Eyewitness HD

Отзывы:

Бренды по названию

Популярные бренды