Kustom Signals Digital Eyewitness HD Скачать руководство пользователя страница 69

Страница: 69 / 70

Index

Manual Part Number:

006-1219-00 Rev. 0

Index–1

Digital Eyewitness

In-Car Video System

Index

Accessory Cable

(Part # 155-3956-25) .......................... 4-5

Basic Cabling Information ...................... 4-1
Basic Digital Eyewitness

System ................................................ 1-1

Careful Placement of Components ............. i
Checking the Order ................................ 1-3
DVR / System Serial Number

Locations ............................................ 6-4

DVR Front Panel .................................... 6-1
DVR Heat Management ......................... 6-3
DVR Rear Panel ..................................... 6-2
Eyewitness

HD System Serial

Numbers ............................................. 1-6

Field Service ............................................... i
Field Verification of File Transfer

Operability .......................................... 8-1

Headliner Mount ..................................... 2-6
Important/Notable Information ..................... i
Initial Checks Prior to Installing

Camera On Windshield or
Headliner Mounting Tab ..................... 3-4

Installation of GPS and Wi-Fi

Antennas ............................................ 5-1

Installation of the Digital Video

Recorder (DVR) .................................. 6-1

Installation of the Mobile Data

Computer (MDC) Option ..................... 7-1

Installer Qualifications ............................ 1-4
Installing an HD Camera with

Optional Headliner Mount
(Part # 050-0615-00) .......................... 3-9

Installing an HD Camera with

Standard Combination Camera/
Wireless Audio Transmitter Base
Mount (Part # 050-0695-04) ............... 3-1

Installing an HD Camera with

Windshield Mount
(Part # 050-0615-00) .......................... 3-5

Installing GPS Components

(Part # 015-1599-00) .......................... 5-1

Installing the Cameras and In-Car

Microphone (ICM) ............................... 3-1

Installing the In-Car Microphone ........... 3-11
Installing the Power Cable

(Part # 155-3957-25) ........................... 4-7

Installing the Rear Seat Camera

with Integrated In-Car
Microphone ....................................... 3-12

Installing the Tablet Monitor

Controller (TMC) ................................. 2-1

Installing Wireless N File Transfer

5.0 GHz Antenna Components
(Part # 050-0860-00) ........................... 5-2

Managing Excess Cable ......................... 4-3
Mini-Octopus (Mini-OTP) Cable

(Part # 155-3952-00) ........................... 4-4

Mounting the DVR ................................... 6-4
Optional Eyewitness

HD System

Components ........................................ 1-2

Order of Installation ................................. 1-4
Power/Ground Connection

Requirements ...................................... 1-6

Preparing the DVR for Mounting ............. 6-4
Preparing the Tablet Monitor

Controller (TMC) for Installation .......... 2-1

Product Description ................................. 1-1
Protecting against RFI (Radio

Frequency Interference) ...................... 1-5

Radio Frequency Interference

(RFI) Prevention .................................. 4-2

Routing and Installing System

Cables ................................................. 4-1

Routing Cables Through

Bulkheads ........................................... 4-2

Side Airbag Precautions ......................... 4-2
Tablet Monitor Controller

Installation ........................................... 2-4

Take Appropriate Steps When

Drilling Holes ........................................... i

TMC Ball and Socket Mount ................... 2-4

Содержание Digital Eyewitness HD







































































Результаты поиска

Содержание Digital Eyewitness HD

Отзывы:

Бренды по названию

Популярные бренды

Kustom Signals Digital Eyewitness HD, Руководство по установке

Результаты поиска

Содержание Digital Eyewitness HD

Отзывы:

Бренды по названию

Популярные бренды