Kustom Signals Digital Eyewitness HD Скачать руководство пользователя страница 10

Product Description 

 

 

 

 

Digital Eyewitness

® 

HD 

In-Car Video System 

1–2 

Manual Part Number: 

006-1219-00 Rev. 0 

 

Optional Eyewitness

®

 HD System Components 

The Eyewitness

®

 HD system may be ordered in many configurations that may include any of 

the following components: 

  Internal 64 GB hard drive (in addition to the removable hard drive – required for 

background recording) 

  Dual wireless audio transmitter (radio)/docking station 

  Mobile Data Computer (MDC) control (in addition to, or instead of, the 7-inch display) 

  Radar interface 

  Window mount or visor mount for primary standalone HD camera (forward facing) 

  Additional rear seat mounted SD camera with integrated in-car microphone (standalone 

in-car microphone (ICM) is not included if rear seat mounted SD camera is ordered) 

  Additional HD camera or cameras (up to three (3) total) with either a windshield mount 

or visor mount 

  GPS  

  File transfer (both wired and wireless 5.0 GHz antenna kit options are available) 

  Ignition modification (used to power the system on when the vehicle ignition key is 

turned to the run position) 

Содержание Digital Eyewitness HD







































































Отзывы: