Konica Minolta CS-7, Руководство по эксплуатации

Страница: 394 / 424

394
10 .2 Error codes and countermeasures
Error code Displayed message Problems/countermeasures
F0I34*
F0I35*
F0I36*
F0I37*
[DR Detector name] cable/cradle connection error
Poor connection of a cable or a cradle .
Please reconnect after checking for a foreign particle
in the connector .
(1) Confirm that the wired connection connector part of
the DR Detector, AeroDR Battery Charger, AeroDR
Battery Charger2 and I/F Cable doesn't have any
foreign objects attached .
(2) Confirm that the I/F Cable is not connected at an
angle .
(3) Reconnect .
F0I38*
[DR Detector name] cable/cradle connection error
Poor connection of a cable or a cradle .
Please reconnect after checking for a foreign particle
in the connector .
(1) Confirm that the wired connection connector part of
the DR Detector, AeroDR Battery Charger, AeroDR
Battery Charger2 and I/F Cable doesn't have any
foreign objects attached .
(2) Check the AeroDR Battery Charger or AeroDR
Battery Charger2 power .
(3) Confirm that the I/F Cable is not connected at an
angle .
(4) Reconnect .
F0I39*
[DR Detector name] power source error
If the panel after rebooting does not recover, contact a
service representative .
(1) Restart the DR Detector .
(2) Contact Konica Minolta technical representatives .
F0I46*
[DR Detector name] power source error
The AeroDR panel cannot be charging because of high
temperature inside the panel .
You can charge it again after cooling down .
If this error occurs frequently, contact a service repre-
sentative .
(1) Move the DR Detector away from an electrical
carpet, a location exposed to direct sunlight, or a
place where heat can build up, then wait until the
temperature falls .
If an error occurs, charging will not be possible .
However, it will be possible to carry out exposures.
(2) If the problem persists, contact Konica Minolta tech-
nical representatives .
F0I47* Please reconnect the cable or the cradle .
(1) Please reconnect the I/F Cable or the AeroDR Bat-
tery Charger .
(2) If the problem persists, contact Konica Minolta tech-
nical representatives .
F0J11*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .
(1) Restart the DR Detector .
(2) Contact Konica Minolta technical representatives .
F0P01*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .
F0Q00*
F0Q01*
[DR Detector name] shock detection
Detected a shock .
Be careful in handling the panel .
The DR Detector is precision equipment, therefore
subjecting it to strong impacts or excessive loads such
as falls and hits may cause it to malfunction .
Be careful in handling the DR Detector .
F0Q02*
F0Q03*
[DR Detector name] shock detection
Detected a shock .
Please run the panel check tool because of the pos-
sibility of malfunction .
The DR Detector may be malfunctioning .
(1) Use the drop/impact panel check tool to check if the
DR Detector is malfunctioning or not .
(2) If an error occurs, contact Konica Minolta technical
representatives .
F0Q10*
F0Q11*
F0Q12*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .
(1) Restart the DR Detector .
(2) Contact Konica Minolta technical representatives .
F2E01*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .
F2E17*
[DR Detector name] version update error
If the panel after rebooting does not recover, contact a
service representative .
F3205*
F3500*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .
F3600*
F3601*
F3604*
F3605*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .
F3606*
F3700*
[DR Detector name] internal error
If the panel after rebooting does not recover, contact a
service representative .