KI Tattoo Flex Screen, Руководство по сборке

Страница: 32 / 52

32
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tattoo™ Screens - Spine Screen Trim
Assembly Instructions
End-of-Run Spacer Installation
1. Per the space-planning layout, locate
the end-of-run screen. Make sure
that screen is near its final location
and is plumb and level.
2. The screen connector comes with
eight molding clips installed (shown
uninstalled, Figure 36), four on each
side. Position the screen connector
up against the vertical frame channel
of the Spine Screen, with clips
oriented as shown. Using a firm
hand, press at the mounting clips
on the screen connector, one at a
time to seat them into the vertical
frame channel at the end of the Spine
Screen (Figure 34 & Detail SS).
3. Position the spacer against the
vertical frame, with the side opening
as desired, and the top facing
upward. If the spacer top is higher
than the top of the Spine Screen's
horizontal frame, the spacer is too
tall at the top and must be squarely
cut off from the bottom. Cut required
amount off the bottom, then press the
side of the spacer with the molding
clips in the vertical frame channel on
the Spine Screen taking care to align
the top of the spacer with the top of
the screen's horizontal frame. Press
forcefully from inside the spacer
at the side, to engage the screen
connector into the channel of the
spacer (Figure 34 & Detail SS).
Note: Two different top caps are
available for Tattoo Screen spacers
and are labeled so on the bottom
of each top cap. An “E” or “I”
is displayed on each top cap to
represent if the cap is for end-of-run
or in-line. As labeled, the top caps
are designed to install to a specific
spacer. Take care and follow the
directions below when installing
the top cap. If proper top cap is
not installed to the proper spacer,
the flat aluminum top cap will not
fit correctly, extending too far and
disassembly and reassembly will be
required.
4. Confirm the base infeed top cap is
labelled “E” on the underside for
end-of-run. Place the spacer top cap
onto the spacer. Align the mounting
hole on the side of the top cap with
the mounting hole in the spacer
cover channel and secure with a
#10-24 x
1
/
2
” Phillips flat head screw.
The base infeed top cap will rest
flush with the flat aluminum top cap
installed in a later step (Figure 34 &
Detail SS).
5. On the rib side of the spacer trim,
space molding clips evenly apart and
press them onto the ribs of the trim
(Figure 35 & Detail TT).
6. Position the spacer trim with
molding clips up against the spacer.
Using a firm hand, press to snap
molding clips of the base infeed
trim into the vertical spacer channel
(Figure 35 & Detail TT).
7. On the rib side of the spacer cover,
space molding clips evenly apart
and press them onto both ribs on the
cover (Figure 35 & Detail UU).
8. Position the space cover with
molding clips up against the spacer.
Using a firm hand, press to snap
moling clips of the spacer cover into
the spacer cover channel (Figure 35
& Detail UU).
Spine
Screen
vertical
frame
screen
connector
molding
clip
#10-24 x / ”
Phillips flat
head screw
1
2
spacer
top cap
(end-of-run)
spacer
(end-of-run)
vertical
frame
channel
Figure 34
Detail SS
Spine
Screen
screen
connector
molding clip
(factory installed)
#10-24 x / ”
Phillips flat
head screw
1
2
spacer
(end-of-run)
vertical
frame
channel
spacer top cap
(end-of-run)
Figure 35
Spine
Screen
spacer trim
(end-of-run)
molding
clip
vertical
spacer
channel
space cover
channel
spacer
cover
spacer
(end-of-run)
Detail TT
vertical
spacer
channel
molding
clip
spacer
trim
Detail UU
molding
clip
spacer cover
channel
spacer
cover