KI Tattoo Flex Screen, Руководство по сборке

Страница: 24 / 52

24
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tattoo™ Screens - Spine Screen 10-Wire Power
Assembly Instructions
10-Wire Base Power Infeed
Spacer (In-Line) Installation
Note: All screens must be
mechanically connected together,
with all 10-wire rigid wireways and
screen-to-screen power connections
appropriately installed before adding
power infeed, or connecting infeed to
power source.
Note: The power infeeds are to be
connected to the power source by
a qualified electrician who must
follow all state and local codes at the
building site and check the electrical
integrity of the finished system.
1. Per the space-planning layout,
determine the location for base
infeed spacer. Make sure that the
screens to receive the base infeed
spacer are near their final location,
and are plumb and level.
2. The two required screen connectors
come with eight molding clips
installed to each (shown uninstalled,
Figure 24), four on each side.
At each Spine Screen end, as
illustrated, position the screen
connector up against the vertical
frame channel of the Spine Screen,
with clips oriented as shown. Using
a firm hand, press at the mounting
clips on the screen connector, one at
a time to seat them into the vertical
frame channel at the end of the Spine
Screen (Figure 24 & Detail II).
3. Position the base infeed spacer
against the vertical frame, with the
side opening as desired, and the
top facing upward. If the base infeed
spacer top is higher than the top of
the Spine Screen's horizontal frame,
the spacer is too tall at the top and
must be squarely cut off from the
bottom. Cut required amount off the
bottom, then press the side of the
base infeed spacer with the molding
clips in the vertical frame channel on
the Spine Screen taking care to align
the top of the base infeed spacer with
the top of the screen's horizontal
frame. Press forcefully from inside
the spacer, to engage the screen
connector/clips of Spine Screen #1
into the channel of the base infeed
spacer. Next, move the Spine Screen
#2 over to align its installed screen
connector/clips with the appropriate
vertical spacer channel. Level and
plumb Spine Screen #2 to #1 by
twisting the height-adjustable glides
clockwise or counter-clockwise until
the frame’s vertical edges are aligned
and tops of screens are at the same
height. Press Spine Screen #2 into
the vertical spacer channel to engage
such that both Spine Screens are
snapped into the base infeed spacer
(Figure 24 & Detail II).
Note:
Two different top caps are
available for Tattoo Screen spacers
and are labeled so on the bottom
of each top cap. An “E” or “I”
is displayed on each top cap to
represent if the cap is for end-of-run
or in-line. As labeled, the top caps
are designed to install to a specific
spacer. Take care and follow the
directions below when installing the
top cap. If top cap is not installed to
the proper spacer, the flat aluminum
top cap will not fit correctly,
extending too far and disassembly
and reassembly will be required.
4. Confirm the base infeed top cap
is labelled “I” on the underside for
inline. Place the base infeed top cap
onto the base infeed spacer. Align
the mounting hole on the side of the
top cap with the mounting hole in
the spacer cover channel and secure
with a #10-24 x
1
/
2
” Phillips flat head
screw. The base infeed top cap will
rest flush with the flat aluminum top
cap installed in a later step
(Figure 24 & Detail II).
5. At the location specified for a
screen-to-screen jumper between the
base infeed spacer, route the jumper
through the pass-through ankles at
each end of the Spine Screen, then
plug the ends into each rigid wireway
of the powered Spine Screens
(Figure 24).
6. Route the 10-wire base power infeed
plug end of the infeed through the
pass-through ankle and plug it
into an open end of a 10-wire rigid
wireway (Figure 24).
Spine
Screen
(#1)
Spine
Screen
(#2)
base infeed
top cap
(in-line)
base infeed
spacer
(in-line)
screen
connector
vertical
frame
channel
molding
clip
molding
clip
#10-24 x / ”
Phillips flat
head screw
1
2
screen-to-screen
10-wire jumper
(21 / ”) 1
4
10-wire
rigid wireway
10-wire
rigid wireway
vertical
spacer
channel
10-wire base
power infeed
Figure 24
Detail II
Spine
Screen
screen
connector
molding clip
(factory installed)
#10-24 x / ”
Phillips flat
head screw
1
2
base
infeed spacer
(in-line)
vertical
frame
channel
base infeed
top cap (in-line)