![background image](http://html2.mh-extra.com/html/keithley/6514/6514_instruction-manual_4064199331.webp)
N
Noise
4-10
Non-decade current gains
11-16
Non-standard coulombs ranges
11-13
O
Offset voltage calibration
18-9
Ohms calibration
19-16
Ohms measurement accuracy
18-15
One-shot triggering
E-3
Options and accessories
1-3
Output queue
13-18
Output trigger specifications
9-12
Overview
13-2
P
Percent (%)
7-5
Perform limit tests
10-11
Performance considerations
2-2
Performance Verification
18-1
Performing the verification test
procedures
18-8
Piezoelectric and stored charge effects
C-3
Power-up
1-10
Power-up sequence
1-11
Preparing for calibration
19-7
Primary address selection
12-7
Programming and reading registers
13-5
Programming enable registers
13-5
Programming example
3-8, 4-9, 5-6, 8-6,
9-10, 10-15
Programming examples
E-2
Programming syntax
12-11
Q
Queues
13-18
R
Range
6-2
Range, units, and digits
6-2
Range, Units, Digits, Rate, and Filters
6-1
Rate
6-6
Reading calibration standard values
H-2
Reading registers
13-6
Reading values
H-2
Rear panel summary
1-8
Recalculating resistance reading limits
18-6
Recall
8-2
Recommended calibration equipment
19-3
Recommended test equipment
18-4
Register bit descriptions
13-11
Relative
7-1, 7-2
Relative, mX+b and Percent (%)
7-1
Remote calibration
H-4
Remote calibration overview
H-4
Remote Operation
12-1
Resetting the calibration code
19-19
Restoring factory defaults
18-9
Routine Maintenance
20-1
RS-232 connections
12-18
RS-232 interface reference
12-17
RS-232 settings
12-17
S
Safety symbols and terms
1-2
SCPI commands
F-10
SCPI programming
1-15, 2-3, 2-18, 3-7, 4-8,
5-5, 8-4, 9-9, 10-12
SCPI programming — digital output
pattern
11-6
SCPI programming — external feedback
11-17
SCPI programming — filters
6-10
SCPI programming — mX+b and percent
7-6
SCPI programming — range and digits
6-4
SCPI programming — rate
6-7
SCPI programming — relative
7-3
SCPI programming — zero check and zero
correct
2-15
SCPI Reference Tables
17-1
SCPI Signal Oriented Measurement
Commands
15-1
Selecting and configuring an interface
12-2
Sending and receiving data
12-17
Serial polling and SRQ
13-9
Service request enable register
13-8
Setting and controlling relative
7-2
Setting digital output lines
11-5
Setting line voltage and replacing line fuse
20-2
Shielded fixture construction
11-12
Sink mode — controlling external devices
11-3
Source mode — logic control
11-5
Specifications
A-1
Status and Error Messages
1-12, B-1
Status byte and service request (SRQ)
13-7
Status byte and service request commands
13-9
Содержание 6514
