![background image](http://html1.mh-extra.com/html/keithley/2750/2750_user-manual_3956564432.webp)
Model 2750 Multimeter/Switch System User’s Manual
IEEE-488 Bus Overview
G-5
Bus management lines
The five bus management lines help to ensure proper interface control and management.
These lines are used to send the uniline commands.
ATN (Attention)
— The ATN state determines how information on the data bus is to be
interpreted.
IFC (Interface Clear)
— The IFC line controls clearing of instruments from the bus.
REN (Remote Enable)
—The REN line is used to place the instrument on the bus in the
remote mode.
EOI (End or Identify)
— The EOI line is used to mark the end of a multi-byte data trans-
fer sequence.
SRQ (Service Request)
— The SRQ line is used by devices when they require service
from the controller.
Handshake lines
The bus handshake lines operate in an interlocked sequence. This method ensures reliable
data transmission regardless of the transfer rate. Generally, data transfer will occur at a
rate determined by the slowest active device on the bus.
One of the three handshake lines is controlled by the source (the talker sending informa-
tion), while the remaining two lines are controlled by accepting devices (the listener or lis-
teners receiving the information). The three handshake lines are:
DAV (DATA VALID)
— The source controls the state of the DAV line to indicate to any
listening devices whether or not data bus information is valid.
NRFD (Not Ready For Data)
— The acceptor controls the state of NRFD. It is used to
signal to the transmitting device to hold off the byte transfer sequence until the accepting
device is ready.
NDAC (Not Data Accepted)
— NDAC is also controlled by the accepting device. The
state of NDAC tells the source whether or not the device has accepted the data byte.
The complete handshake sequence for one data byte is shown in
placed on the data lines, the source checks to see that NRFD is high, indicating that all
active devices are ready. At the same time, NDAC should be low from the previous byte
transfer. If these conditions are not met, the source must wait until NDAC and NRFD have
the correct status. If the source is a controller, NRFD and NDAC must be stable for at least
100ns after ATN is set true. Because of the possibility of a bus hang up, many controllers
have time-out routines that display messages in case the transfer sequence stops for any
reason.
2750-900-01.book Page 5 Wednesday, August 3, 2011 7:56 AM
Содержание 2750
