Kaixin DCU12 Скачать руководство пользователя страница 81

Full Digital Color Doppler Ultrasonic Diagnostic Instrument (Vet)                                                                            User’s Manual V1.00 

 

- 73 - 

Chapter Twenty-two      System Maintenance 

 

The  system  maintenance  should be performed by  the  user  and  service  engineer.  Users  shall be  in  full 

charge of maintenance, repair and operation of the system after purchasing the product. 

 
 
 

 

22.1 Maintenance by users 

22.1.1 System cleaning and disinfection 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1. Clean the probe 

(1) Must wear sterilized gloves to prevent possible infection. 
(2)  Rinse  the  probe  with  water  or  soapy  water  to  remove  all  contaminants,  or  use  a  soft  urethane 

sponge to wipe the probe. Do not use brushes as it may damage the probe. 

(3) After finishing the rinsing, use a sterilized cloth or gauze to wipe the water on the surface of probe. 

Do not dry the probe by heating it. 

2. High-level disinfection 

Please follow the disinfection method provided in this user’s manual for disinfection. 
(1) Before disinfection, wear sterilized gloves to prevent possible infection; 
(2)  You  must  clean  the  probe  before  disinfection.  Recommend  the  solution  to  disinfect  in  the 

following table. 

Warning

: Turn off the instrument and pull out the power supply wire before cleaning 

every  instrument  of  the  system.  It  may  cause  electric  shock  if  clean  the  system  under 
power is on. 

Warning

There is no any waterproof device in the system. Do not splash any water or 

liquor into the system when cleaning or maintaining; otherwise it will cause malfunction 
or electric shock. 

Attention

:

 

 

1. To prevent possible infection, it is advisable to wear sterilized gloves when cleaning, 

disinfecting the ultrasonic probe. 

2. Clean the probe with sterile water to remove the residual chemicals after disinfection, 

because the residual chemicals may be harmful for humans.   

3. Kaixin Company will not make any guarantee for the efficacy of disinfector. Please 

contact the appropriate manufacturer for details.

 

Warning:   

Do not place the ultrasonic probe connector into water or disinfection,   
as it may

 

cause electric shock. 

Attention

:

 

 

1. In the process of cleaning and disinfection, avoid probe overheat (exceeding 60

) as it 

may be damaged or deformed under excessive heat. 

2. In the operation of disinfection, please refer to medical institutions disinfection technical 

specifications. 

Warning

: The following parts of the equipment are not serviced or maintained while in 

use with the patient. 

Содержание DCU12
























































































Отзывы: