manualshive.com logo in svg

Kaixin DCU12, Руководство пользователя, Страница: 17 / 87

Поделиться
Скачать
Kaixin DCU12 Скачать руководство пользователя страница 17

Full Digital Color Doppler Ultrasonic Diagnostic Instrument (Vet)                                                                            User’s Manual V1.00 

 

- 9 - 

5.1 System placement 

Please  carefully  read  through  and  fully  understand  the  safety  cautions  before  moving  and  placing  the 

system. 

1.  Unpack  the  instrument  case  and  check  the  goods  for  its  completeness  according  to  the  packing  list 

furnished. 

2. Place the instrument on a stable and leveled position. 
3. Leave adequate space of 20 centimeters as minimum from rear, left and right side of the instrument. 
 

 
 
 
5.2 Probe brackets installation 

The probe bracket should be mounted behind the main unit. 

5.3 Ultrasonic probe installation 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
5.3.1 Probe connection 

 

 

 
 
 

1. Shutdown the system; open the probe locking knob, and insert the probe connector into the probe 

socket at the back of the main unit until the metal spring plates is evenly contacted. Tightly press the 
connector. 

2. Rotate the probe locking knob 90 degree clockwise and lock it, shown as the figure

. 

5.3.2 Probe disconnection 

Shutdown the system; rotate the locking knob 90 degree counterclockwise, pull out the probe connector 

vertically. 

5.4 Connect to power 

1. Connect to the power adapter 

Insert the output plug of adapter into DC input interface, which is at the back of main unit. 

Attention: 

Adequate space from rear, left and right side of the machine shall be reserved, 

or the machine may malfunction under excessive heat inside the enclosure.

 

Attention:   

1. Turn off the ultrasonic system before disconnecting the probe. Disconnecting the probe 

with system power on may damage the system or probe. 

2. Before disconnecting the probe, place the probe on the probe bracket so that the probe 

may not be damaged or injury person by unexpected fall. 

3. Freeze the instrument when instrument is start-up without operation to increase of service 

life of probe. 

4. Repeat available machine time should be more than 5 minutes to avoid turn on/off power 

supply in short time. 

Warning: 

 

1. Do not use the probe not provided by our company, otherwise the equipment and the probe 

will cause damage, and may cause fire in extreme cases.

 

2. Check the ultrasonic probe and connecting cable after diagnostic operation. Use of 

defective probe may cause electric shock to the patient. 

3. Do not strike the probe; using the damaged probe may cause electric shock to the patient. 
4. Unauthorized disassembly of the probe shall be prohibited as it may cause electric shock.   

Warning:

  Before  connecting  or  using  the  probe,  make  sure  that  the  probe,  connecting 

cable  and  connector  are  in  normal  condition  (free  of  cracks  or  drop).  Use  of  defective 
probe may cause electric shock.

 

Содержание DCU12
























































































Отзывы:

Нет отзывов