Jungheinrich ERE 120 Скачать руководство пользователя страница 44

Страница: 44 / 179

02.15 EN

Exposing the battery

WARNING!

An unsecured truck can cause accidents

Parking the truck on an incline or with a raised load handler is dangerous and is
strictly prohibited.

Park the truck on a level surface. In special cases the truck may need to be secured
with wedges.

Fully lower the load handler.

Select a place to park where no other people are at risk of injury from the lowered
load handler.

If the brakes are not working, place wedges underneath the wheels of the truck to
prevent it from moving.

CAUTION!

A closing battery panel can pose a trapping hazard

If the battery cover is not opened fully, it can suddenly close on its own and cause
bruising. The battery cover is only properly opened at an angle greater than 90°. It is
then held by gravity.

Open the battery cover as far as the stop.

Requirements

– Park the truck on a level surface.
– Park the truck securely, see "Parking the

truck securely" on page 65.

Procedure

• Depress the Emergency Disconnect (8).
• Pull up the battery panel (39) using the

recess and lift it back (38).

The battery connector and battery retainer
can be accessed

Содержание ERE 120




















































































































































































Результаты поиска

Содержание ERE 120

Отзывы:

Бренды по названию

Популярные бренды

Jungheinrich ERE 120, Руководство по эксплуатации

Результаты поиска

Содержание ERE 120

Отзывы:

Бренды по названию

Популярные бренды