Jungheinrich ERE 120 Скачать руководство пользователя | Manualshive

Страница: 167 / 179

background image

03.13 EN

10

5.2

Operation

5.2.1 Commissioning

Checks and operations to be performed before starting daily work

Procedure

• Make sure the battery is in physically good condition.
• Make sure the terminals are correct (positive to positive and negative to negative)

and check that contacts on the battery terminal conducting system are secure.

• Check the terminal screw torques (M10 = 23 ±1 Nm) of the terminal conductors and

connectors.

• Re-charge the battery.
• Charge the battery.

Check completed.

5.2.2 Discharging the battery

Z

To achieve an optimum useful life avoid operational discharges of more than 60%
of nominal capacity.

Z

If the battery is discharged during operation by more than 80% of rated capacity the
useful life of the battery will reduce significantly. Fully or partially discharged
batteries must be re-charged immediately and not left unattended.

5.2.3 Charging the battery

WARNING!

The gases produced during charging can cause explosions

The battery gives off a mixture of oxygen and hydrogen (electrolytic gas) during
charging. Gassing is a chemical process. This gas mixture is highly explosive and
must not be ignited.

X

Always disconnect the charger and truck before connecting or disconnecting the
charger and battery.

X

The charger must be adapted to the battery in terms of voltage, charge capacity
and battery technology.

X

Before charging, check all cables and plug connections for visible signs of damage.

X

Ventilate the room in which the truck is being charged.

X

Battery cell surfaces must remain exposed during charging in order to ensure
sufficient ventilation, see truck operating instructions, chapter D, Charging the
Battery.

X

Do not smoke and avoid naked flames when handling batteries.

X

Wherever an industrial truck is parked for charging there must be no inflammable
material or consumables capable of creating sparks within a minimum distance of
2 m from the truck.

X

Fire protection equipment must be available.

X

Do not place any metallic objects on the battery.

X

Always follow the safety regulations of the battery and charger station
manufacturers.

«
...
165
166
167
168
169
...
»

Содержание ERE 120




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERE 120

Бренд: DAF Страницы: 20

Бренд: SANO Страницы: 8

Бренд: Terex Страницы: 410

Бренд: AUSA Страницы: 72

Бренд: Still Страницы: 288

Бренд: Still Страницы: 470

Бренд: Volvo Страницы: 104

Бренд: Kleton Страницы: 8

Бренд: Kleton Страницы: 8

Бренд: Kleton Страницы: 8

HARRINGTON HPC500 Series

Бренд: KITO Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды