background image

02.15 EN

18

3.2

Functional Description

Safety Mechanisms

An enclosed, smooth truck perimter with rounded edges ensures safe handling of the
truck. The wheels are surrounded by a solid skirt.

When released a gas pressure spring pushes the tiller up and activates braking.

If the truck touches a person, the red collision safety switch changes the travel
direction in pedestrian mode when travelling in drive direction with the platform and
the side restraints folded up (

o

). The truck brakes, travels away from the operator

and stops. This prevents the operator from being hit.
The collision safety feature can also be activated for rider mode (

o

).

Activating the Emergency Disconnect switch rapidly cuts out all electrical functions in
hazardous situations.

The protective mesh (

o

) protects the operator from sliding loads.

Emergency Stop safety feature

The Emergency Stop is activated by the traction controller. Each time the truck is
switched on the system performed a self diagnosis. If an error is detected, the truck
automatically brakes to a halt. Control displays in the CanDis display instrument (

o

)

indicate the Emergency Stop.

CAUTION!

The truck brakes automatically

If the truck detects that signals which are required have not been received, or if it
detects an error, the system reacts by triggering an emergency stop, either by braking
the truck to a halt or until a valid signal status has been reached.

X

In rider mode: Take up a stable standing position and hold on with both hands. 

X

In pedestrian mode: Remain at a suitable distance from the truck during operation. 

Hydraulic system

Pressing the lifting button starts the pump unit, supplying hydraulic oil from the oil
reservoir to the lift cylinder. Pressing the lifting button raises the load handler at a
constant speed; pressing the lowering button lowers the load handler.

Ergonomic lift (

o

) (ERE C20)

For lifting and lowering, the truck is equipped with support arm lift (initial lift) with the
maximum lift capacity and mast lift (high lift) with a lower lift capacity.

Drive system

A fixed AC three-phase motor actuates the drive wheel via a bevel spur gearbox. The
electronic traction controller ensures smooth drive-motor-speed control and hence
smooth starting, powerful acceleration and electrically controlled braking with energy
regeneration. The driver can choose from 3 travel programs depending on the load
and the environment: from high-performance to energy-saving.

o

Содержание ERE 120




















































































































































































Отзывы: