manualshive.com logo in svg

JRC JAN-701B -, Инструкция по эксплуатации, Страница: 538 / 564

Поделиться
Скачать
JRC JAN-701B - Скачать руководство пользователя страница 538

 

12

 

Display and View of Multi Window 

12-4

 

12.2 

View of Each Information 

12.2.1  View of Navigation Information 

This section describes the screen configuration and displayed items of the block that displays navigation 
information. 

 

(1)   Course Bar Block 

 
 

 

 
 

1) Planned Course 

The course in the navigation plan that was programmed into the ECDIS system is displayed by 
the 

▼

 mark. 

2)  Gyro (Gyro course) 

The ship’s heading according to the gyro compass is displayed. 

3) Course 
 

The course from GPS is displayed. 

4)  CTS (Course to steer) 

When the route tracking mode is selected in the ECDIS, the course used for automatic sailing is 
displayed by the 

▲

 mark. 

5)  ROT (Rate of turn)

*1

 

The rate of turn per minute is displayed. 
The full span value of the displayed graph can be set to 30, 60, 90, 120 or 150 degrees/minute 
from the “Setup” panel. 

 
*1  ROT is displayed when this information is sent from the gyro compass. 

1) 

2) 

3) 

4) 

5) 

3)

1)

5)

4) 2)

Содержание JAN-701B -





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов