manualshive.com logo in svg

JRC JAN-701B -, Инструкция по эксплуатации, Страница: 205 / 564

Поделиться
Скачать
JRC JAN-701B - Скачать руководство пользователя страница 205

 

3    Basic Operation of ECDIS 

3-143

ECDIS 

 

3.26 Logbook 

You can display the logbook where various voyage information is written. The recorded items and the 
items shown on the logbook table are selectable with the “logbook Setting”panel . How to display the 
logbook and how to select the items to be saved are explained here. 
 

3.26.1  Displaying the Logbook 

The items displayed in the logbook are selectable. For the selection, see the next 3.26.2 “Logbook 
Setting ”. 

 

1)  In the normal menu 

Select [MENU] - [(7) Main] - [(7) Logbook] in that order. 
The “Logbook” panel opens. Contents of the logbook are as follows: 
(Note that, to see all the contents, scroll the panel.) 

・ 

No. 

・

 

Date 

・

 

Time 

・

 

Event (kind of alarm, Event Mark Navtex, etc. -- depends on the 
“Logbook setting” panel settings.), 

・

 

POSN1 

・

 

POSN2 

・

 

Latitude 

・

 

Longitude 

・

 

COG 

・

 

SOG 

・

 

HDG 

・

 

STW 

・

 

Av. Speed 4h 

・

 

Av. Speed 24h (average speed recent 4/24 hours) 

・

 

Voyage DIST. (G ) 

・

 

Voyage DIST. (W) (Voyage distance (Ground)/(Water)) 

・

 

Charts 

・

 

Set 

・

 

Drift 

・

 

Wind Dir. (direction) 

・

 

Wind Speed 

・

 

Wave Dir. (direction) 

・

 

Wave Height 

・

 

Air Press (pressure) 

・

 

Air Temperature. 

・

 

Water Temperature. 

・

 

Engine Rev. (revolution) 

・

 

Comments 

Содержание JAN-701B -





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов