JRC JAN-701B - Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 564

JRC JAN-701B - Скачать руководство пользователя страница 321

4 Route Planning

4-59

ECDIS

(1) Alternate Route Editing mode

In the normal menu

Select [MENU] - [(2) Route] - [(2) Create Alternate Route] in that order.

The Alternate Route Editing screen as shown below will open. (This screen is the same as for
Graphic Editor.)

[Alternate Route Editing Screen]

Opening the Alternate Route Editing Menu:
On the display panel in the Alternate Route Editing mode

Rotate the trackball to move the cursor on upper part of screen.

The special menu for Alternate Route Editor will open. (This menu is the same as for Graphic
Editor.)

(2) Creating Alternate Route

The following shows the way how to make an alternate route using the buttons on the screens.
(When you use the EBL/VRM on the operation panel, see 4.1.3.8 “Creating a Route Using
EBL/VRM Keys and Dials”.
Operate while watching the cursor position displayed at the bottom of the display panel.

Note:

• Alternate routes will be displayed in orange so that the modified section can be differentiated from

the original route.

«
...
319
320
321
322
323
...
»

Содержание JAN-701B -





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов