Jonsered 1188S CE Скачать руководство пользователя

Страница: 54 / 96

Speed quick set

Each control lever has a MICRO button (2).

If you press the button one time the speed for all movements will drop to to 50% of maximum.

If you press the button twice the speed for all movements will drop to to 20% of maximum.

If you press the button three times the speed for all movements will be 100% (maximum).

The selected settings will appear on the display.

If a control lever doesn’t move for 5 minutes, the operating system switches to Stand By. Press the
stand by button on the control panel in the cabin twice to restart the system

8.4. Buttons and indicator lights on the PDF

Power On

(1)

Green light on: The system is on.

Green light flashing: A stop button is pressed.

Service

(5)

Green light on: Time to service the crane.

Red light on: A non-critical error detected in the

system.

Red light flashing: Critical error is stopping the

crane. Diagnostic required.

Red double flash: CAN error, crane stops.

The control system Multidrive2 [option]

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды