Jonsered 1188S CE Скачать руководство пользователя | Manualshive

Страница: 79 / 96

background image

12.5. Adjust the lateral clearance of the boom and/or
hydraulic extension

Turn the bearing covers an equal amount on both sides.

Turn the covers all the way closed. Then open them one
quarter of a turn.

12.6. Adjust the chain in the telescope

཰

ཱ

ི

ཱི

ུ

ཱུ

ྲྀ

(1) second boom
(2) chain tensioner
(3) roller
(4) chain tensioner
(5) extension 1
(6) roller
(7) extension 2

The correct tightness prevents the chains from overloading and wearing out too quickly. Correct
adjusted chains will also not jump off the grove in the roller.

1.

Retract the extensions. Lower the grapple to the ground.

2.

Loosen the adjustment screw of the top chain fastener until the chain is visibly loose.

3.

Tighten the adjustment screw of the bottom chain. Extension 2 will retract until the extensions
come in contact with each other. Check that the top chain is still loose. Loosen the adjustment
screw of the bottom fastener until a small gap is created between the nut and the second
boom and extra chain tension is removed.

4.

Raise the 2nd boom until it is level and keep the grapple near the ground. Extend the
extensions. Slightly retract the extensions (2 to 5 cm) to loosen the top chain. Leave the 2nd
boom in the air to avoid the top chain from tighten.

Maintenance and Service

Jonsered 1188S CE

79

«
...
77
78
79
80
81
...
»

Содержание 1188S CE

































































































Отзывы:

Нет отзывов

Похожие инструкции для 1188S CE

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: Öhlins Страницы: 8

Бренд: ?HC Страницы: 2

PRO-FORM ab GLIDER

Бренд: ICON Health & Fitness Страницы: 16

Бренд: Raytec Страницы: 8

HomeFill HF2POST6

Бренд: Invacare Страницы: 24

Бренд: WhizRider Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды