Jonsered 1188S CE Скачать руководство пользователя

Страница: 34 / 96

WARNING

• Never use the extension boom as a jack. This could damage the slewing

bearings and the connection between the crane column and the crane base.

• Do not lift a load above yourself or the cab.
• Be careful, in particular, the safety system gives an early warning!
• When loading the vehicle:

Take the load off the stabiliser legs by withdrawing them slightly. The stabiliser
legs must remain in light contact with the ground.

CAUTION

• Operate the crane using smooth and gentle lever movements.
• If a cylinder is at its end position, free the operating lever. Otherwise overheating

can occur.

3.7.1. Use of lifting equipment

DANGER

• Only use lifting accessories that are

suitable for your crane. Contact a HIAB
service workshop.

• Never attempt to install add-on lifting

accessories yourself!

• Add-on lifting accessories may only be

installed by an authorised HIAB service
workshop.

• When using lifting accessories, follow the

instructions supplied with the equipment!

• Watch out for hazards!
• Never try to adjust lifting accessories when

you are working on the crane!

After the lifting accessories have been fitted:

1. Check that the lifting accessories are securely fixed.
2. Only after this should you use your crane.

Safety precautions and warnings

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды