Jonsered 1188S CE Скачать руководство пользователя

Страница: 49 / 96

LED status

CAN status (yellow)

OFF

Unit lacks power or will not start.

Slow flash

No communication via CAN-bus.

Rapid flash

Fault in CAN-bus communication in the unit. For the Master-unit: Fault in
Master unit’s CAN-bus communication or in another part of the system.

Steady glow

CAN-bus communication works normally for the unit. For the Master-unit:
CAN-bus communication works normally for the entire system.

LED status

CPU status (green)

OFF

Unit lacks power or will not start.

Slow flash

Standby position or configuration position.

Rapid flash

Internal fault in the unit. For the Master-unit: Fault in the Master unit or in
other units connected to the system.

Steady glow

Unit works normally. For the Master-unit: The entire system works normally

Ground Control Unit (GCU) [option]

The GCU- unit is a controller used together with the
TimberTronics control system. The GCU is connected to
the crane via a cable.

When the GCU is connected, all levers on the main control
valve will be locked and the crane is operated with reduced
speed.

(1) Stop button

(2) Button to be pressed when using the crane operating
buttons.

ཱ

཰

The control system TimberTronics [option]

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды