Jonsered 1188S CE Скачать руководство пользователя

Страница: 29 / 96

WARNING

• Use low force when placing the stabiliser legs on the ground.
• Do not raise the vehicle with the stabiliser legs!

If you raise the vehicle with the stabiliser legs, this may damage the stabiliser
legs.

DANGER

Do not stand in front of the boom system
when operating the crane out of the parking
position.

Preparation for use

WARNING

Make sure that there are no unauthorised
persons within the operating range of your
crane!

WARNING

• If a part of the crane comes in contact with

an electricity line, you will be electrocuted!

• Maintain the following minimum distances

between the crane and overhead
electricity

lines,

unless

otherwise

prescribed by national rules.

Safety precautions and warnings

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды