Jonsered 1188S CE Скачать руководство пользователя

Страница: 63 / 96

11. Ending crane operation

11.1. Placing the stabiliser system in transport position

DANGER

Do not stand in the stabiliser legs, tilting area.

WARNING

Do not put your foot under the stabiliser leg

DANGER

Always ensure that the stabiliser legs and the stabiliser extensions are in transport
position and securely locked.

Crane with tiltable stabiliser legs

1. Raise the stabiliser leg carefully slightly from the

ground.

2. Unlock the stabiliser leg lock (1). Make sure that it

remains in the released position.

WARNING

Do not stand behind the stabiliser leg. Do not touch the stabiliser leg either.

3. Raise the stabiliser leg slowly until the plate touches the bar on the “inside” of the stabiliser leg.
4. Continue raising the stabiliser leg carefully. It will now move backwards and perform a rotary

movement.

Ending crane operation

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды