Jonsered 1188S CE Скачать руководство пользователя

Страница: 57 / 96

NOTE

Pressure in the hoses can prevent the quick couplings from connecting: You can
release the pressure

- by pressing open the quick-acting coupling’s stem

- from the pressure gauge adapter, using a suitable connector.

9.3. Electric tiltable seat [option]

To operate the seat up or down.

Push and hold button (1) and operate the switch (2) at the
same time.

WARNING

Do not stand in front of moving parts. They can cause injuries.

Operating the stabiliser system

WARNING

All levers must be in neutral position.

DANGER

When you are operating the stabiliser extensions: Make sure that you have full
view of the stabiliser extensions. Do not stand in front of hydraulically operated
stabiliser extensions.

Starting crane operation

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды