Jonsered 1188S CE Скачать руководство пользователя

Страница: 43 / 96

7. The control system TimberTronics [option]

7.1. The TimberTronics control system

The TimberTronics control system is developed for Loglift and Jonsered. With the TimberTronics
control system you can:

• Monitor the crane’s operating data
• Display error messages and operational warnings
• Troubleshoot easy

The control system also provides integrated weighing, showing how heavy load is being handled at
any time [option].

Press the standby button on the cabins control panel to start the system. For safety reasons, the
joysticks are blocked when the system is started. Press a menu button on a joystick to activate
them.

7.2. Components in the TimberTronics system

(1) Two joysticks (placed inside the cabin)

(2) MASTER unit box (placed underneath the cabin)

(3) CRANE unit box (placed underneath the cabin)

(4) Display (placed inside the cabin)

(5) Ground Control Unit (GCU) [Option]

(6) Regulators (placed on the control valve)

The system has two operating mode.

Stabiliser mode is used for cabin up/down and to operate
the stabilisers.

Crane mode is used to operate the crane.

Use the MENU buttons on the joysticks to step between the modes. Present mode is shown on the
display.

Joysticks, steering schema

ཱི

ུ

཰

ཱ

ི

ཱུ

The control system TimberTronics [option]

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды